ar1840b4111dd

Remove/install oil level sensor

Type ar · topic 18.40 · version 0103 · 2020-02-04

Applies to: Engine 906.999 in model 368 with code M09 (EPA 04) Engine 924.925 in model 368 with code M09 (EPA 04) Engine 924.929 in model 384 with code M09 (EPA 04) Engine 926.942 in model 382 Engine 926.950 in model 368 with code M09 (EPA 04)

Where it sits

Function group 1 Engine › 18 Engine lubrication, engine oil cooling › 18.40 Oil level/oil pressure sensor — Series 368 · Series 382 · Series 384 · Series 906 (models 999)

EinPAS 15 Engine › 15.20 Engine lubrication system › 15.20.12 Sensor/switch/wiring harness — Series 368 · Series 382 · Series 384 · Series 906 (models 999)

Also applies to engines/gearboxes: 924 925, 924 929, 926 942, 926 950

AR18.40-B-4111DD

Remove/install oil level sensor

03.02.2020

Engine	906.999 in model 368
	with code M09 (EPA 04)
Engine	924.925 in model 368
	with code M09 (EPA 04)
Engine	924.929 in model 384
	with code M09 (EPA 04)
Engine	926.942 in model 382
Engine	926.950 in model 368
	with code M09 (EPA 04)

Remove/install oil level sensor

G18.40-3105-08

1	Fitting connector		3	Electric wires		B14	Oil level sensor
2	Electric harness of the engine		4	Oil pan

 	Remove/install
1	Vacuum or drain the engine oil
2	Detach the plug connector (1) from the oil level sensor (B14) on the engine electric wiring harness (2)
3	Detach the plug connector (1) from the engine
4	Uncover the electric wire (3) of the oil level sensor (B14) up to the oil pan (4)	 Install: Install the new binding straps.
5	Remove the oil level sensor (B14) from the oil pan (4)	 Install: Replace the sealing ring.
		 .Oil level sensor in the oil pan	*BA18.40-B-1002-01A
6	Install in reverse order
	Check
7	Refill the engine oil circuit	.	AR18.00-B-1600DD
8	Check the engine oil level, if necessary, adjust to the correct level
 Warning	Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.	Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
9	Turn on the engine and pay attention to the oil pressure indicator while the engine is in idle speed	 Start the engine through the starter for a period not to exceed 90 seconds. Wait about 2 minutes before repeating the starting procedure. Do not accelerate the engine at full speed until the oil pressure is indicated on the display. Otherwise, the engine can be damaged.
		 Please see the Operating Instructions Manual
		 The oil pressure must be shown after approximately 10 seconds.
		.Engine oil pressure, minimum permissible	*BE18.00-B-1001-01A
10	Turn off the engine and check whether there are leaks

Oil pressure

Number	Designation			Engine 904.9, 906.9	Engine 924.9, 926.9
BE18.00-B-1001-01A	Engine oil pressure, minimum permissible	idle rotation	bar	0,5	0,5
		maximum rotation	bar	2,5	2,5

 Oil level and pressure indicator

Number	Designation		Engine 904.9, 906.9	Engine 924.9, 926.9
BA18.40-B-1002-01A	Oil level sensor in the oil pan	Nm	60	60

Referenced documents

ar1800b1600dd Filling the engine oil circuit
as0000z000501a Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.