S18.20-A002-78
1 | Screw | 6 | Screw | 10 | Bracket | ||
2 | Screw | 7 | Screw | 11 | Electrical connectors | ||
3 | Screw | 8 | Screw | 12 | Retaining clamp | ||
4 | Screw | 9 | Oil filter housing | 13 | Mounting clip | ||
5 | Screw |
9 | Oil filter housing |
14 | Sealing rings |
S18.20-A003-71
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
Caution | Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil | Wear protective gloves, protective clothing and safety glasses. | |
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
| Remove | ||
1 | Drain off coolant. | ||
2 | Remove the alternator | ||
3 | Remove poly-V-belt tensioning device. | ||
4 | Remove charge-air distributor. | ||
5 | Remove left engine carrier. | ||
6 | Remove bracket (10). | ||
7 | Disconnect electrical connectors (11). | ||
8 | Unclip retaining clip (13). | Clip remover | |
9 | Detach retaining clamps (12) of the electrical wiring harness. | ||
10 | Remove screws(1 to 8). | ||
11 | Remove oil filter housing (9) from the crankcase. | Catch escaping coolant and motor oil. | |
12 | Remove seals (14) from oil filter housing (9). | ||
13 | Seal openings on the oil filter housing (9) and on the crankcase with suitable stop plugs. | Record plug | |
| Clean | ||
14 | Clean sealing surfaces on the oil filter housing (9) and on the crankcase with a lint-free cloth. | ||
| Install | ||
15 | Remove stop plugs from the oil filter housing (9) and from the crankcase. | ||
16 | Mount new seals (14) on the oil filter housing (9). | ||
17 | Position oil filter housing (9) on the crankcase in the installation position. | ||
18 | Tighten screws (1 to 8) to stage 1 in numerical order. | Bolt, oil filter housing to crankcase | |
19 | Tighten screws (1 to 8) to stage 2 in numerical order. | Bolt, oil filter housing to crankcase | |
20 | Attach retaining clamps (12) of the electrical wiring harness. | ||
21 | Clip in retaining clip (13). | ||
22 | Contact the electrical connectors (11). | ||
23 | Install bracket (10). | ||
24 | Install left engine carrier. | ||
25 | Install charge-air distributor. | ||
26 | Install clamping device for poly-V belt. | ||
27 | Install alternator. | ||
28 | Fill in coolant. | ||
| Check | ||
29 | Check the engine oil level in the instrument cluster and correct if necessary. | Engine oil | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
30 | Perform engine test run and check engine for leaktightness in the area around the oil filter housing (9). |
452 589 01 63 00
Clip remover
129 589 00 91 00
Record plug
Referenced documents
- ah0000p500001a Notes on avoiding damage through contamination and foreign objects
- ar0941s8683ea Remove/install charge air distributor
- ar1325s3220ea Remove/install poly-V-belt tensioning device
- ar1540s5032ea Remove/install alternator
- ar2000s1142e Drain/pour in coolant
- ar2210s4350ea Remove/install left engine support
- as0000z000501a Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.
- as1800z000101a Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil
- as2000z000101a Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant.