ar0761p1401qk

Remove/install throttle valve actuator

Type ar · topic 07.61 · version 0205 · 2008-03-26

Applies to: ENGINES 271.940 in MODEL 203.042 /242 /742, 209.342 /442 ENGINES 271.941 in MODELS 211.042 /242 ENGINES 271.946 in MODEL 203.046 /246 /746 ENGINES 271.948 in MODEL 203.040 /240 /740 ENGINES 271.942 in MODEL 203.043 /243 /743, 209.343 ENGINES 271.921 in MODEL 203.730 ENGINES 271.955 in MODEL 209.341 /441 ENGINES 271.956 in MODEL 211.041 /241 ENGINES 271.957 in MODEL 203.741

Where it sits

Function group 1 Engine › 07 Mixture formation › 07.61 ME fuel injection/ ignition system — Series 203 (models 040, 042, 043, 046, 240, 242, 243, 246, 730, 740, 741, 742, 743, 746) · Series 209 (models 341, 342, 343, 441, 442) · Series 211 (models 041, 042, 241, 242)

EinPAS 15 Engine › 15.45 Engine management › 15.45.31 Actuator motor/actuator/mixture controller — Series 203 (models 040, 042, 043, 046, 240, 242, 243, 246, 730, 740, 741, 742, 743, 746) · Series 209 (models 341, 342, 343, 441, 442) · Series 211 (models 041, 042, 241, 242)

Also applies to engines/gearboxes: 271 921, 271 940, 271 941, 271 942, 271 946, 271 948, 271 955, 271 956, 271 957

AR07.61-P-1401QK

Remove/install throttle valve actuator

21.2.08

ENGINES 271.940 in MODEL 203.042 /242 /742, 209.342 /442

ENGINES 271.941 in MODELS 211.042 /242

ENGINES 271.946 in MODEL 203.046 /246 /746

ENGINES 271.948 in MODEL 203.040 /240 /740

ENGINES 271.942 in MODEL 203.043 /243 /743, 209.343

ENGINES 271.921 in MODEL 203.730

ENGINES 271.955 in MODEL 209.341 /441

ENGINES 271.956 in MODEL 211.041 /241

ENGINES 271.957 in MODEL 203.741

Remove/install throttle valve actuator

P30.20-2051-06

Shown on model 209

1 Bolts

2 Intake air duct

3 Pressure connection fitting

4 Connector

M16/6 Throttle valve actuator

Modification notes

16.6.04

"Disconnect/connect battery ground line" removed

Remove/install

1

Open engine hood

Model 203

AR88.40-P-1000P

MODEL 209

AR88.40-P-1000Q

Model 211

AR88.40-P-1000T

2

Remove Intake air line (2)

3.1

Remove pressure connection (3) to throttle valve actuator (M16/6)

Model 203, 209

Installation: Do not apply grease to openings of the pressure connection (3). The pressure buildup by the compressor would loosen the pressure connection (3) from the throttle valve actuator (M16/6)

3.2

Release pressure connection (3) from throttle valve actuator (M16/6)

Model 211

Installation: Do not apply grease to openings of the pressure connection (3). The pressure buildup by the compressor would loosen the pressure connection (3) from the throttle valve actuator (M16/6)

4

Detach vacuum line of purge valve at throttle valve actuator (M16/6)

Model 203, 209

5

Remove plug (4) from throttle valve actuator (M16/6)

6

Remove bolt (1)

*BA30.20-P-1002-01C

7

Remove the throttle valve actuator (M16/6)

Installation: Observe leading guides, otherwise leaks may occur.

8

Install in the reverse order

9

Read out fault memory and erase

Stored faults which may be caused by assembly work, test work, removed lines or a simulation, must be processed and erased in fault memories after completing the work.

Connect STAR DIAGNOSIS and read out fault memory

AD00.00-P-2000-04A

Electronic accelerator pedal actuator

Number

Designation

Engine
271

BA30.20-P-1002-01C

Bolt, throttle valve actuator to intake manifold

Nm

9

Referenced documents