AR07.07-P-1454GZ | Removing/installing hot film mass air flow sensor together with the air intake pipe | 23.11.04 |
ENGINE 113.964 in MODEL 164.175
P07.07-2055-06
1 Air cleaner housing
2 Electrical connector
3 Vent line
4 Vent line
5 Top catch
6 Bottom catch
7 Air intake connection
8 Lock
9 Sealing ring
B2/5 Hot film MAF sensor
| Removing/installing | ||
Danger! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | When moving components, ensure that no body parts or limbs are within the operating range of moving parts. | |
1 | Open engine hood and raise to vertical position | ||
2 | Remove air cleaner housing (1). | ||
3 | Remove the electrical connector (2) at the hot film mass air flow sensor (B2/5) | ||
4 | Detach vent line (3) from hot film mass air flow sensor (B2/5) | ||
5 | Release vent line (4) from bracket at hot film mass air flow sensor (B2/5). | ||
6 | Open top catch (5) at top of hot film mass air flow sensor (B2/5) | ||
7 | Use a hook to pull up bottom catch (6) at top of air intake connection (7) | To do this, push the hot film mass air flow sensor (B2/5) as far back as possible, until the lower catch (6) cannot latch again. | |
8 | Use a screwdriver to press down lock (8) on the air intake connection (7) | To do this, push the hot film mass air flow sensor (B2/5) as far back as possible, until the catch (8) cannot latch again. | |
9 | Remove hot film mass air flow sensor (B2/5) from throttle valve actuator | Installation: Check sealing ring (9), replace if required. Check the sealing ring between air inlet connection (7) and hot film mass air flow sensor , replace if required. Check upper lock (5), lower lock (6) and lock (8); replace locks or air intake connections (7) as required. | |
10 | Unclip pneumatic line on AIR management control system from brackets on the air intake connection (7) | ||
11 | Install in reverse order | ||
12.1 | Read out fault memory and erase if required | When replacing the hot film mass air flow sensor (B2/5). | |
| Connect up STAR DIAGNOSIS and read out fault memory | ||
STAR DIAGNOSIS diagnosis system | |||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns when working in engine during starting procedure | Secure vehicle to prevent it from moving. | |
13 | Conduct engine test run and check the intake system for leaks | If a leak is found, determine the cause and rectify, otherwise engine malfunctions may result. |
Commercially available tools
Referenced documents
- ad0000p200004a
- ad0000p200004a Connect STAR DIAGNOSIS and read out fault memory
- ar0910p1150gz Remove/install air cleaner housing
- ar0910p1150gza Remove/install air filter housing
- ar0910p1150gzb Remove/install air filter housing
- ar0910p1150gzc Remove/install air filter housing
- ar0910p1150gzd Remove/install air filter housing
- ar0910p1150gzg Remove/install air filter housing
- ar0910p1150gzs Remove/install air filter housing
- ar8840p1000gz Open engine hood, move to upright position and close
- as0000z000501a Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.
- as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.