AN80.50-P-0100D | Retrofit interior motion sensor | 3.5.99 |
MODELS 202.07 /08 /18 as of 1.6.97 with CODE (551a) Antitheft alarm system (ATA)
MODEL 202.19 with CODE (551a) Antitheft alarm system (ATA)
P82.55-0263-06
A26/4 Left infrared (IR) interior motion sensor transmitter-receiver
A26/5 Right infrared (IR) interior motion sensor transmitter and receiver
B39 Left rear glass breakage sensor
B39/1 Right rear glass breakage sensor
B39/4 Rear window breakage sensor
| Removing | ||
1 | Remove load space floor | ||
2 | Disconnect ground cable of battery | ||
| |||
3 | Remove fuse box in loading space | Do not disconnect lines. | |
| |||
4 | Remove rear passenger compartment side trim panel | Models 202.07/08/18/19, left and right | |
| |||
5 | Expose PSE control module | ||
6 | Remove front seat | left and right | |
| |||
7 | Remove rear seat cushion | ||
8 | Fold rear seat back forwards | ||
9 | Remove side cushion on rear seat backrest | ||
| |||
10 | Remove left and right door sill molding | ||
11 | Remove floor covering at rear left and right and place to one side | ||
12 | Remove floor covering at front left and right and place to one side | ||
13 | Open cable ducts at left and right in the center | ||
14 | Remove paneling on B-pillar | left and right | |
| |||
15 | Remove paneling on right C-pillar | left and right | |
| |||
16 | Remove grab handle and rod mounting at rear left and right | ||
17 | Remove rear roof frame paneling | Left | |
| |||
18 | Remove liner on tailgate | ||
| |||
19 | Remove side window in load space | The standard side windows in the left and right-hand sides of the load space are to be replaced by glass panels with integrated glass breakage sensors. | |
| |||
20 | Remove tailgate window pane | Similar to the side windows, the standard rear window is to be replaced by a glass panel with integrated glass breakage sensor. | |
| |||
| Installing | ||
21 | Install side window in load space | Install the side windows at left and right only, install the removed paneling in the load space only after installing the interior motion sensor first. | |
| |||
22 | Install tailgate | Install window only, fit door lining after the interior motion sensor has been installed. | |
| |||
23 | Prepare B-pillar paneling for installation of interior motion sensor transmitter and receiver | ||
24 | Retrofit wiring harness | Interior motion sensor wiring harness | |
25 | Retrofit interior motion sensor transmitter and receiver | ||
26 | Fit remaining parts to vehicle | ||
27 | Check functionality of interior motion sensor | ||
28 | Amend special equipment code 882 in FDOK |
Parts ordering notes
Part no. | Designation | Quantity |
Design group 67 | Side window in load space with left glass breakage sensor | 1 |
Design group 67 | Side window in load space with right glass breakage sensor | 1 |
Design group 67 | Tailgate window pane with glass breakage sensor | 1 |
Design group 82 | Left infrared (IR) interior motion sensor transmitter-receiver | 1 |
Design group 82 | Right infrared (IR) interior motion sensor transmitter and receiver | 1 |
Design group 82 | Interior motion sensor wiring harness | 1 |
Design group 82 | Switch | 1 |
Design group 82 | Cap | 2 |
Referenced documents
- an8050p000101f Retrofitting wiring harness
- an8050p010001b Retrofitting transmitter and receiver
- an8050p010006a Preparing B-pillar paneling for installation of interior motion sensor transmitter and receiver
- ar5410p0003a Disconnect/connect battery's ground cable
- ar5415p1324a Removing and installing fuse box in trunk
- ar6720p3550e Remove/install rear window
- ar6730p4050e Remove/install side window in load compartment
- ar6830p1050a Removing and installing liner on tailgate
- ar6830p4470a Removing and installing rear roof frame cover
- ar6830p4490ea Removing and installing lining on C-pillar
- ar6830p4700e Removing and installing lining on B-pillar
- ar6830p4780a Removing and installing side paneling in rear
- ar9110p1000e Removing and installing front seats
- ar9112p1710a Removing and installing side cushion on rear backrest