S49.20-A038-79
1 | AdBlue® tank | 3 | Screw | 5 | Filling hose | ||
2 | Bolts | 4 | Heat shield | 6 | Electrical wiring harness |
1 | AdBlue® tank |
4 | Heat shield |
7 | Bolts |
8 | Vent line |
S49.20-A039-76
1 | AdBlue® tank |
6 | Electrical wiring harness |
9 | Electrical connector |
10 | Retaining clamp |
11 | Mounting clip |
12 | AdBlue® line |
13 | Connection fitting |
S49.20-A040-76
Warning | Risk of burn injuries and scalding when working on AdBlue(R) lines and the component parts attached to them. Risk of injury to skin and eyes when handling AdBlue(R). Risk of poisoning caused by swallowing AdBlue(R) | Pour AdBlue® only into suitable containers. Wait until the pressure is released before starting any work on the exhaust aftertreatment system. | |
Topical note | Notes on use, material properties and handling of NOx reducing agent | ||
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
| Remove/install | ||
1 | Empty the AdBlue® tank (1). | ||
2 | Remove underfloor paneling at left. | ||
Installation: Install left underfloor paneling only after the leak test. | |||
3 | Remove bolts_(7). | ||
4 | Remove heat shield (4) downward. | ||
5 | Disconnect electrical connections (9). | ||
6 | Detach retaining clamps (10) from the AdBlue® container (1). | ||
7 | Unclip retaining clip (11) and being electrical wiring harness (6) out of the working area. | Clip remover | |
8 | Release AdBlue® line (12) from the connection fitting (13) and remove. | Collect escaping AdBlue®. | |
9 | Seal openings with suitable stop plug. | Record plug | |
10 | Unclip AdBlue® line (12) from the AdBlue® container (1) and bring out of the working area. | ||
11 | Remove filling hose (5) from the AdBlue® container (1). | Collect escaping AdBlue®. | |
Hose clamp pliers | |||
12 | Seal openings using suitable protective covers. | Set of protective covers | |
13 | Release and disconnect bleed line (8) from the separating point. | ||
14 | Seal openings with suitable stop plug. | Record plug | |
15 | Remove bolt (3) . | Bolt, AdBlue® tank to body | |
16 | Support AdBlue® container (1) centrally. | ||
| 000 588 11 62 00 Major assembly mount | ||
| 000 588 10 62 00 Support plate | ||
17 | Remove screws (2). | Bolt, AdBlue® tank to body | |
18 | Drain off AdBlue® container (1) and bring out of the working area. | ||
19 | Install in the reverse order. | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
20 | Perform engine test run and check in the area of the AdBlue® container (1) for leak tightness. |
454 589 00 37 00
Hose clamp pliers
001 589 01 91 00
Set of protective covers
452 589 01 63 00
Clip remover
129 589 00 91 00
Record plug
Έγγραφα που αναφέρονται
- ah0000p500001a Υποδείξεις για την αποφυγή ζημιών από ακαθαρσίες και ξένα σώματα
- ah4920n000201a Οδηγίες για τη χρήση, τις ιδιότητες και το χειρισμό του αναγωγικού μέσου NOx
- ah5400p000101a Οδηγίες για την αποφυγή ζημιών σε ηλεκτρονικά εξαρτήματα λόγω ηλεκτροστατικής εκκένωσης
- ar4920s2015ea
- ar6130s1001e
- as0000z000501a Κίνδυνος ατυχήματος λόγω αυτόματης εκκίνησης κατά τη λειτουργία του κινητήρα. Κίνδυνος τραυματισμού με μώλωπες και εγκαύματα σε �
- as4920z000201a Κίνδυνος εγκαύματος κατά τις εργασίες σε σωλήνες AdBlue(R) και σε συνδεδεμένα εξαρτήματα. Κίνδυνος τραυματισμού στο δέρμα και τα μάτι�
- ws0100p0092b 000 588 11 62 00 Βάση μηχανικών συγκροτημάτων
- ws2600p3309b 000 588 10 62 00 Πλάκα στήριξης