AR42.15-B-0008A | Disassemble/assemble automatic linkage adjuster | 12.02.16 |
Vehicle 364.### #C, 364.### #A, 364.### #M, 364.### #D, 364.### #B, 382.### #C, 382.### #A, 382.### #M, 382.### #D, 382.### #B, 384.### #C, 384.### #A, 384.### #M, 384.### #D, 384.### #B, 386.### #C, 386.### #A, 386.### #M, 386.### #D, 386.### #B, 388.### #C, 388.### #A, 388.### #M, 388.### #D, 388.### #B, 397.### #C, 397.### #A, 397.### #M, 397.### #D, 397.### #B
Vehicle 634.### #C, 634.### #M, 634.### #B, 634.### #D, 660.### #C, 660.### #M, 660.### #B, 660.### #D, 664.### #C, 664.### #M, 664.### #B, 664.### #D, 682.### #C, 682.### #M, 682.### #B, 682.### #D
Vehicle 684.189, 693, 694, 695, 696
Vehicle 958.1
B42.15-0013-06
Haldex automatic adjuster
1 Housing
2 Bushing
3 Front threaded cover
4 Axial needle bearing
5 Coupling ring
6 Blocking spring
7 Gear
8 Sealing ring
9 Bearing
10 Worm gear
11 Rack
12 Ring gear
13 Sealing ring
14 Gasket
15 Control unit
16 Bolts
17 Expansion cover
18 Spring
19 Spring
20 Grease fitting
21 Stop washer
22 Helical spring
23 Rear threaded cover
24 Rivet
25 Identification plate
B42.15-0011-09
| Disassemble | ||
1 | Loosen the attachment bolts (16) of the control unit (15) and remove it | Attach the adjuster to a bench vice with the clamps protected by aluminum plates. | |
2 | Remove the rack (11) by compressing springs (18) and (19) | ||
3 | Remove the expansion cover (17) and remove springs (18) and (19) | Use an adequate mandrel. | |
4 | Remove the rear threaded cover (23), the helical spring (22) and the stop washer (21) | Remove the rivet (24) and loosen the cover (23) with a special tool. | |
5 | Remove the front threaded cover (3) and the needle bearing (4) | Remove the rivet (24) and loosen the cover (3) with a special tool. | |
6 | Loosen the uni-directional coupling (5), (6) and (7) and displace bearing (9), removing the worm gear (10) | Use the mandrel and the bushing found in the tool kit. | |
7 | Remove the pinion (12) and the sealing rings (13) | ||
Danger! | Risk of explosion due to flames, risk of poisoning due to fuel inhaling and ingestion, and also risk of injuries due to contact of the skin and eyes with the fuel | It is forbidden to start fire, sparks, open flames and smoking. Only store fuel in appropriate containers and duly identified. When handling fuel, use appropriate protective clothing and equipment. | |
| Clean | ||
8 | Procede to cleaning the parts | Check them for wear and, if necessary, replace them. | |
| Measure | ||
9 | Start the inspection and control | With the help of a measuring instrument, check: | |
- Diameter of the housing receptacle (1). | |||
- Diameter of the ring gear receptacle (12). | |||
- Diameter of the worm gear receptacle (10). | |||
- Diameter of the ring gear (12). | |||
- Diameter of the worm gear shaft (10). | |||
External micrometer from 50 to 75 mm. | |||
Internal diameter gauge (sudden) from 35 to 60 mm. | |||
Dial gauge. | |||
| Assemble | ||
Replace the parts belonging to the repair kit. | |||
10 | Assemble the pinion (12) together with the sealing rings (13), in the housing (1) | The ring gear (12) must be assembled with the collar pointing upwards. | |
11 | Assemble the worm gear (10) duly lubricated into the housing (1), ensure free movement by turning it until the ring gear (12) has completed one rotation | Press the bearing until its edge touches the housing. | |
12 | Assemble the set of parts of the uni-directional coupling (5), (6) and (7) duly lubricated into the housing (1) | Keep the pressure until the parts of the set fit together. | |
13 | Install the sealing ring (8) in the worm gear groove (10) and, after attaching the greased axial needle bearing (4) on the threaded cover (3), install into the housing (1) | Using a special tool, apply the specified torque on the threaded cover (3), check whether the worm gear moves freely (10). | |
| |||
14 | Check the worm gear axial clearance (10) | Kit of special tools supplied by Haldex do Brasil under code 78340. | |
15 | Insert springs (18) and (19), fit the rack (11) and insert the expansion cover (17) with the convex side pointing outwards | Check the correct positioning of springs (18) and (19) over the rack hook (11). | |
16 | Assemble the control unit (15) with a new sealing gasket (14), attaching it with bolts (16) | Check the correct fitting of the groove on the rack hook (11). | |
17 | Measure the height of the uni-directional coupling teeth | Kit of special tools supplied by Haldex do Brasil under code 78340. | |
18 | Assemble the stop washer (21) with the spherical salience pointing to the worm gear (10) , the helical spring (22) and the rear threaded cover (23) duly lubricated, insert the rivet (24) | With the help of the special tool, insert the cover (23) for 4 turns. | |
19 | Adjust the automatic adjuster (1) and lubricate it | Kit of special tools supplied by Haldex do Brasil under code 78340. | |
Test values for mechanical system
Número | Denominação | Vehicles 364, 382, 384, 386, 397, 664, 682, 693, 694, 695, with drum brake front axle | Vehicles 388, 660, 696, with drum brake front axle | |||
BE42.15-B-1005-01A | Maximum diameter of the automatic adjuster housing | For the gear | mm | 62.20 | 62.20 | |
For the worm gear | mm | 16.15 | 16.5 | |||
BE42.15-B-1006-01A | Minimum diameter of the automatic adjuster gear | mm | 61.87 | 61.87 | ||
BE42.15-B-1007-01A | Minimum diameter of the worm gear, mounting side on the housing | mm | 15.90 | 15.90 | ||
BE42.15-B-1008-01A | Worm gear axial clearance | mm | 0.15 - 0.60 | 0.15 - 0.60 | ||
BE42.15-B-1009-01A | Minimum height of the unidirectional tapered coupling teeth | mm | 0.08 | 0.08 | ||
Test values for mechanical system
Número | Denominação | Vehicles 382.154, 388, 660, 696, with drum brake front axle | Vehicles 384.067, 693, 694, 695, 958.1 with rear brake front axle | |||
BE42.15-B-1005-01A | Maximum diameter of the automatic adjuster housing | For the gear | mm | 62.20 | 62.20 | |
For the worm gear | mm | 16.15 | 16.15 | |||
BE42.15-B-1006-01A | Minimum diameter of the automatic adjuster gear | mm | 61.87 | 61.87 | ||
BE42.15-B-1007-01A | Minimum diameter of the worm gear, mounting side on the housing | mm | 15.90 | 15.90 | ||
BE42.15-B-1008-01A | Worm gear axial clearance | mm | 0.15 - 0.60 | 0.15 - 0.60 | ||
BE42.15-B-1009-01A | Minimum height of the unidirectional tapered coupling teeth | mm | 0.08 | 0.08 | ||
Brake mechanical system
Número | Denominação | Chassis 364; 368; 382; 388; 397; 634; 660; 664 with front axle with drum brake | Chassis 384; 386; 682; 693; 694; 695 with front axle with drum brake, except axle 733.0 | |||
BA42.15-B-1004-01B | Front threaded cover of the automatic adjuster | Nm | 50 | 50 | ||
Brake mechanical system
Número | Denominação | Chassis 384; 386; 682; 693; 694; 695 with front axle 733.0 with drum brake | Chassis 364; 368; 382; 384; 386; 388; 397; 634; 660; 664 with rear axle with drum brake, except rear axle 740.6/7/8 | |||
BA42.15-B-1004-01B | Front threaded cover of the automatic adjuster | Nm | 50 | 50 | ||
Brake mechanical system
Número | Denominação | Chassis 384.067; 693; 694; 695; 958.1 with rear axle with drum brake, except rear axle 740.6/7/8 | Chassis 364; 382; 388; 397; 660; 664 with rear axle 740.6/7/8 with drum brake | |||
BA42.15-B-1004-01B | Front threaded cover of the automatic adjuster | Nm | 50 | 50 | ||
Brake mechanical system
Número | Denominação | Chassis 693; 695; 696 with rear axle 740.6/7/8 with drum brake | |||
BA42.15-B-1004-01B | Front threaded cover of the automatic adjuster | Nm | 50 | ||
001 589 53 21 00
Dial gauge
Produtos para reparos
Número | Denominação | Número de pedido |
BR00.45-B-1002-04A | Kerosene | - |
Produtos para reparos
Número | Denominação | Número de pedido |
BR00.45-B-1003-06A | Grease as per DBL 6804 - Class 267.0 | - |
Referenzierte Dokumente
- ar4215b000801a Automatischen Gestängesteller einstellen
- ar4215b000802a
- ar4215b000803a Axialspiel des automatischen Gestängestellers prüfen
- as4700b000101a