Remove/install seat belt with emergency tensioning retractor · ar9140p0630cw · Mercedes-Benz WIS

AR91.40-P-0630CW

Remove/install seat belt with emergency tensioning retractor

19.9.14

MODEL

204, 212, 218

Remove/install seat belt with emergency tensioning retractor

P91.40-2736-09

Shown on model 204.0 with code (299) PRE-SAFE

1	Upper trim panel	5	Screw/bolt (Model 204 with code (299) PRE-SAFE, model 212, 218)	9	Screw
2	Lower trim panel	6	Electrical connector (model 204 with code (299) PRE-SAFE, model 212, 218)	10	Electrical connector
3	Screw	7	Electrical wiring harness (model 204 with code (299) PRE-SAFE, model 212, 218)	R12/1	Driver ETR [GUS] squib
4	Seat belt guide bracket	8	Automatic belt retractor	R12/2	Front passenger ETR [GUS] squib

Model 204.0/2/3, 212, shown on model 204.0

11	Screw
12	Seat belt guide

P91.40-2749-04

 	Remove/install
 Danger !	Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units.	Store airbag units with deployment side facing up; do not expose to temperatures greater than 100 °C. When working on these units, disconnect the power supply.	AS91.00-Z-0001-01A
 Danger !	Risk of injury. Injury may result when the tension in the spring in the automatic belt retractor is released.	Never disassemble automatic belt retractors.	AS91.00-Z-0002-01A
	Notes on performing repair, body work and welding on vehicles with airbags and RTE units		AH91.00-P-0002-01M
	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Assessment of airbag and belt tensioner units in accident vehicles		AH91.00-P-0006-01B
	Legal requirements on handling and storing airbags and emergency tensioning retractor units		AH91.00-P-0004-01A
1.1	Remove belt end fitting at left or right front seat	MODEL 204.0/2/9, 212, 218
		 MODEL 204.0/2/9	*BA91.40-P-1003-01P
		 MODEL 212, 218	*BA91.40-P-1005-01Q
1.2	Remove belt end fitting at left or right B-pillar	MODEL 204.3
		 Bolt at front belt end fitting	*BA91.40-P-1003-01P
2	Disconnect battery ground line	MODEL 204	AR54.10-P-0003CW
		MODEL 212, 218	AR54.10-P-0003EW
3	Remove upper paneling (1) and lower paneling (2) on B-pillar
4	Remove bolt (3) at belt guide bracket (4)	 MODEL 204	*BA91.40-P-1002-01P
		 MODEL 212, 218.3 MODEL 218.9	*BA91.40-P-1003-01Q
5.1	Remove bolt (11) and remove belt guide (12)	MODEL 204.0/2/3, 212
		 MODEL 204	*BA91.40-P-1010-01P
		 MODEL 212	*BA91.40-P-1004-01Q
5.2	Route seat belt out of belt guide	MODEL 218
6	Remove bolt (9) from automatic belt retractor (8)	 MODEL 204	*BA91.40-P-1001-01P
		 MODEL 212, 218	*BA91.40-P-1001-01Q
7.1	Remove screw/bolt (5) from automatic belt retractor (8)	MODEL 204 with CODE 299 (PRE-SAFE® system) MODEL 212 without CODE Z04 (Light armoring) MODEL 218
		 MODEL 212 without CODE Z04 (Light armoring) MODEL 218.3 MODEL 218.9	*BA91.40-P-1001-01Q
		 MODEL 204	*BA91.40-P-1001-01P
7.2	Remove screw/bolt (5) and remove protective plate	MODEL 212 with CODE Z04 (Light armoring)
		 Installation: Press protective plate upward when screwing in screw/bolt (5).
		 Bolt, front automatic belt retractor	*BA91.40-P-1001-01Q
8	Lead automatic belt retractor (8) out of B-pillar
9	Disconnect electrical connector (10) from driver emergency tensioning retractor squib (R12/1) or front passenger emergency tensioning retractor squib (R12/2)
10	Detach electrical connector (6) and expose electrical wiring harness (7)	MODEL 204 with CODE 299 (PRE-SAFE® system) MODEL 212, 218
11	Remove seat belt with emergency tensioning retractor	 If the seat belt with emergency tensioning retractor is replaced, the defective one must be disposed of properly:
12	Install in the reverse order
13	Connect Star Diagnosis and perform initial startup of PRE-SAFE	MODEL 204 with CODE 299 (PRE-SAFE® system) MODEL 212, 218 After replacing the seat belt with emergency tensioning retractor.
			AD00.00-P-2000-04A