P88.20-3915-09
Shown on model 222 up to model year 2018 |
9 | Cover | 10 | Side paneling |
P88.20-3916-09
Shown on model 222 up to model year 2018 |
1 | Bumper | 4 | Expansion rivet | 7 | Expansion rivet | ||
2 | Fender liner | 5 | Bolts | 8 | Bolts | ||
3 | Screw | 6 | Bolts |
P88.20-4083-09
Shown on model 222 up to model year 2018 |
1 | Bumper | 11 | Electrical connector |
P88.20-4124-07
Shown on model 222 up to model year 2018 with code M002 (Engines with exhaust gas turbocharger with charge air cooling) |
1 | Bumper | 8 | Bolts | 13 | Hose | ||
5 | Bolts | 12 | Mounting clip |
Shown on model 222 from model year 2018 |
14 | Plug |
P88.20-4823-06
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Notes on sensor system for trunk lid opening/closing | |||
| Remove/install | ||
1 | Remove charger feed socket flap | Model 222.163/173 | |
2 | Remove rear lamps units | ||
3 | Remove rear center assembly trim | ||
4 | Remove left and right cover (9) | ||
5 | Remove left and right stop plug (14) | ||
6 | Unscrew screws of bumper (1) through the openings (arrows A) | ||
7 | Release left and right side trim (10) and push to one side | ||
8 | Unscrew nuts of bumper (1) through the openings (arrows B and C) | ||
9 | Detach underfloor paneling at rear | ||
Loosen underfloor paneling at rear until bolts (8) are accessible. | |||
10 | Unscrew screws (5, 8) | ||
11 | Unclip retaining clip (12) with hose (13) | Model 222 | |
12 | Detach left and right fender liner (2) and push toward side | ||
13 | Remove bolts (3) | ||
14 | Disconnect electrical connections (11) and unclip wiring harness | The number of electrical connectors (11) varies depending on the equipment. | |
15 | Remove expansion rivets (4, 7) | ||
16 | Remove bolts (6) | ||
17 | Unclip bumper (1) from left and right rear wheel arches | ||
18 | Unclip bumper (1) from rear fenders and in area of rear lamp units | Helper required. | |
19 | Remove bumper (1) | Helper required. | |
20 | Install in the reverse order | ||
| Check | ||
21 | Check whether active parking assist is ready for operation | Model 222 | |
Switch on ignition, switch on active parking assist, engage reverse gear and release parking brake. Active Parking Assist performs a self-test, the warning displays signal operational readiness. | |||
22 | Check whether blind spot assist is ready for operation | Model 222 | |
Switch on ignition. The operation and warning indicators in the outside mirrors illuminate red and then yellow. |
Henviste dokumenter
- ah5400p000101a Oplysninger med henblik på at undgå skader på elektroniske komponenter på grund af elektrostatisk afladning
- ah8061p000101a Oplysninger om HANDS-FREE ACCESS
- ar5410p5110lfh Stikdåseklap forsyning oplader af-, påmonteres
- ar6130p1001lf
- ar6830p4600lf
- ar8210p4905lf Af- og påmontering af baglygte
- ar8810p1400lf
- as0000z001101a Fare for personskade pga. fastklemning eller knusning af fingre ved af-, påmontering og indstillingsarbejde på motorhjelm og bagklap, døre, dæksler og soltag.