ar8370w5600b

Remove/install burner housing/afterburner pipe

Type ar · emne 83.70 · version 0104 · 2004-10-13

Gælder for: MODEL 950, 952, 953, 954 with BODY 942.899 with CODE (H64) Eberspächer D9W hot water auxiliary heater'

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 3 Karrosseri › 83 Klimatisering › 83.70 Parkeringsvarmesystem, ekstra varmesystem, ekstra varmeapparat — Serie 942 (modeller 899) · Serie 950 · Serie 952 · Serie 953 · Serie 954

EinPAS 39 Varmesystem/ventilation/køling › 39.25 Parkeringsvarme/ekstra varmesystem › 39.25.30 varmeapparat — Serie 942 (modeller 899) · Serie 950 · Serie 952 · Serie 953 · Serie 954

AR83.70-W-5600B

Remove/install burner housing/afterburner pipe

30.8.96

MODEL 950, 952, 953, 954 with BODY 942.899 with CODE (H64) Eberspächer D9W hot water auxiliary heater

Remove/install burner housing/afterburner pipe

W83.70-0010-06

1 Burner housing

2 Burner tube

3 Screw

4 Heat exchanger

9 Fuel pipe

10 Line grommet

Remove/install burner housing/afterburner pipe

W83.70-0011-06

1 Burner housing

2 Burner tube

5 Screw

6 Gasket

7 Cotton felt ring

8 Journals

11 Projection

12 Recess

Remove/Install

1

Disconnect ground lead from battery

Do not interrupt main battery current in heater mode or in the run-on phase.

Danger!

Risk of injury caused by body parts being jammed and crushed when tilting cab

Ensure that no one is within the tilting range of the cab during tilting. Always tilt the cab all the way to the end position and secure with the safety strut.

AS60.80-Z-0001-01A

2

Tilt cab

3

Remove heater

AR83.70-W-5302B

4

Remove combustion air blower

AR83.70-W-5557B

5

Remove burner housing (1) with burner tube (2) from heat exchanger (4)

If burner housing sticks

Place screwdriver in groove (arrow A).

*BA83.70-N-1017-03A

6

Unscrew screws (5) from burner housing

*BA83.70-N-1010-03A

7

Remove burner tube with gasket (6)

Guide burner tube out of burner housing with tilting movements (direction of arrow) until the fuel line (9) has been pulled out of both line grommets (10).

Installation:
Guide burner tube into burner housing with fuel line attached (tension-free). Do not bend fuel line.

8

Remove the gasket

Installation:

The burner tube has projections (11) for the seal recesses (12).

9

Release cotton felt ring (7) from the journals (8) in the seat and remove

Installation:

Only touch new cotton felt ring at aluminum seat ring and carefully insert.

10

Install in the reverse order

Danger!

Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit

Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation and wear protective gloves.

AS83.70-Z-0002-01A

11

Check function of stationary heater

AR83.70-W-5302-02B

Stationary heater unit

Number

Designation

Models
950, 952, 953, 954
with body 942.899
with (CODE H64) "Eberspächer D9W" heater unit

BA83.70-N-1010-03A

Bolt, combustion tube to burner housing

Nm

3.5

BA83.70-N-1017-03A

Bolt, combustion tube to heat exchanger

Nm

3

Henviste dokumenter