ar8370w5302na

Remove/install heater unit

Type ar · emne 83.70 · version 0100 · 2014-04-24

Gælder for: MODEL 967 with CODE D6P (Auxiliary hot air heater, 2000 W) with CODE F1P (S cab) without CODE F1R (L-cab)

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 3 Karrosseri › 83 Klimatisering › 83.70 Parkeringsvarmesystem, ekstra varmesystem, ekstra varmeapparat — Serie 967

EinPAS 39 Varmesystem/ventilation/køling › 39.25 Parkeringsvarme/ekstra varmesystem › 39.25.30 varmeapparat — Serie 967

AR83.70-W-5302NA

Remove/install heater unit

13.03.2014

MODEL

967

with CODE D6P (Auxiliary hot air heater, 2000 W)

with CODE F1P (S cab)

without CODE F1R (L-cab)

Remove/install heater unit

W83.70-1326-09

1

Nuts

4

Nuts

7

Fuel hose

2

Nut

5

Clip

3

Exhaust pipe

6

Fuel line

Remove/install heater unit

8

Stowage compartment

9

Cover

10

Electrical connector

11

Fastening bracket

12

Preheating hose

A904

Warm air auxiliary heater

W83.70-1510-06

Danger !

Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit

Do not operate stationary heater, auxiliary heater or engine with heater booster in closed rooms or when refueling. Allow heater unit to cool down after operation and wear protective gloves.

AS83.70-Z-0002-01A

Danger !

Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.

Wear protective gloves, protective clothing and safety glasses, if necessary.

AS00.00-Z-0002-01A

Danger !

Risk of injury caused by body parts being pinched or crushed as cab is tilted

Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut.

AS60.80-Z-0001-01A

Notes on tilting the cab

AH60.80-N-0003-01A

Remove/install

1

Tilt cab

2

Unscrew nuts (1, 2) and remove exhaust pipe (3)

Nut, heater exhaust pipe to cab floor

*BA83.70-N-1006-03NA

3

Unscrew nuts (4)

Nut, heater to cab floor

*BA83.70-N-1005-03NA

4

Open clamp (5) and pull fuel line (6) out of fuel hose (7)

5

Remove clamp (5)

6

Lower cab

7

Remove stowage compartment (8)

8

Remove cover (9)

9

Disconnect electrical connector (10) from heater for warm air auxiliary heater (A904)

Do not interrupt the power supply in heating mode or during the run-on phase.

10

Remove connector socket of electrical connector (10) from mounting bracket (11)

11

Remove preheating hose (12) from heater for warm air auxiliary heater (A904)

12

Pull out electrical lines of heater for warm air auxiliary heater (A904) under the insulation mat

13

Remove heater for warm air auxiliary heater (A904) upwards

Installation: Check seal on flange of heater for warm air auxiliary heater (A904) for damage, replace if necessary.

14

Install in the reverse order

15

Check heater for warm air auxiliary heater (A904) for proper operation

See operator's manual of heater for warm air auxiliary heater (A904).

Auxiliary heater heating unit

Number

Designation

Model 967 with code D6P

BA83.70-N-1005-03NA

Nut, heater to cab floor

Nm

5

Auxiliary heater heating unit

Number

Designation

Model 967 with code D6P

BA83.70-N-1006-03NA

Nut, heater exhaust pipe to cab floor

Nm

5

Henviste dokumenter