AR83.70-W-5302L | Remove/install heater unit | 28.6.06 |
MODEL 375.1 with BODY 375.850
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 375.3 with BODY 375.820
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 375.4 with BODY 375.860
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 940, 942, 943, 944 with BODY 944.890
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 950, 952, 953, 954 with BODY 940.890
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL 970, 972, 974, 975, 976 with BODY 972.890
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
MODEL NAB374.602 /651 with BODY 374.870
with CODE (F04) Cab L (long)
with CODE (HZ3) Warm air auxiliary heater, 2000W
W83.70-1328-06
1 Air intake pipe
2 Fuel pipe
3 Hose clamp
4 Nut
5 Fuel hose
6 Muffler
7 Nut
W83.70-1329-06
8 Heater unit
9 Hot air pipe
10 Heater unit electrical connector
| Remove/install | ||
Danger! | Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit | Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation and wear protective gloves. | |
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
1 | Tilt cab | Except for model 970, 972, 974, 975, 976 with body 972.890 | |
| Notes on tilting the cab | ||
2 | Remove air intake pipe (1) | ||
3 | Undo nuts (4) and remove muffler (6) | | |
4 | Unscrew nuts (7). | | |
5 | Pull fuel line (2) out of fuel hose (5) | To do so, detach hose clamp (3) | |
6 | Detach hose clamp (3) from fuel hose (5) | To ease the removal and installation process of the heater unit (8) the hose clamp (3) must be detached from the fuel hose (5). | |
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
7 | Lower cab | Except for model 970, 972, 974, 975, 976 with body 972.890 | |
| Notes on tilting the cab | ||
8 | Disconnect warm air pipe (9) from heater (8) | ||
9 | Detach heater unit electrical connector (10) | ||
10 | Remove heater unit (8) upwards | Installation: Check the flange gasket for signs of damage and replace if necessary. | |
11 | Install in the reverse order | ||
12 | Check heater unit (8) for proper operation | See heater unit's operating instructions. |
Stationary heater unit
Number | Designation | Model | Model | Model | ||
BA83.70-N-1005-03F | Nut of heater to cab floor | Nm | 5 | 5 | 5 | |
Stationary heater unit
Number | Designation | Model | Model | Model | ||
BA83.70-N-1005-03F | Nut of heater to cab floor | Nm | 5 | 5 | 5 | |
Stationary heater unit
Henviste dokumenter
- ah6080n000301a Oplysninger om tipning af førerhus
- as6080z000101a Fare for personskade ved fastklemning og knusning, når førerhuset tippes
- as8370z000201a Fare for eksplosion på grund af brændstofdampe, fare for forgiftning ved indånding af forbrændingsgas og fare for personskade på grund af forbrændinger, under eller efter at varmesystemet har været i drift.