Remove/install interior sliding door emergency release

AR72.40-D-1009A

Remove/install interior sliding door emergency release

05.12.2019

Model

906.657

with code P0E (Sprinter Tourer master code)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code P0F (Master code for Sprinter Tourer 19+1 Inland)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code P0G (Master code Sprinter Tourer 16+1)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code P0H (Master code Sprinter Tourer 19+1)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code PE4 (DCAA bus master code, Argen)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

Model

906.657

with code PE5 (Mastercode, bus seats on raised base, Argen)

with code T16 (Sliding door right)

with code T55 (Electric operation of sliding door on right)

1

Sliding door emergency release

2

Door trim

3

Electrical line

4

Cable

5

Adjustment screw

6

Rocker

7

Electrical connectors

1

Sliding door emergency release

8

Bolts

11

Nut

3

Electrical line

9

Lever

12

Circuit

4

Cable

10

Cover

 Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Remove lower door trim (2)

MODEL 906.657 except CODE ZO1 (James Cook Compact camper) except CODE ZO2 (James Cook Classic camper)

AR72.16-D-6610G

2

Expose electrical line (3)

3

Disconnect electrical line (3) from electrical connections (7)

 Fasten cord as assembly aid to electrical line (3).

4

Unfasten counternut from adjustment screw (5) and screw in adjustment screw (5)

AR72.16-D-2214A

 Only unfasten until pull wire on rocker (6) is freely accessible.

 Installation: Adjust control cable (4) on sliding door emergency release (1).

5

Open cover (10) on sliding door emergency release (1)

6

Turn lever (9) downward

7

Unscrew bolt (8)

 Pay attention to installation position. Various bolts (8) are installed.

8

Pull sliding door emergency release (1) with electrical line (3) and control cable (4) out of sliding door until control cable (4) is accessible

9

Remove clamp (12) from lever (9)

 Check pull wire of control cable (4) for damage.

 Installation: Secure pull wire of control cable (4) with clamp (12).

Depending on findings



Install new pull wire of control cable (4) in place of damaged pull wire.

Route control cables for closing system

AR72.16-D-2210-02A

10

Unfasten nut (11) and unscrew control cable (4) from sliding door emergency release (1)

 Installation: Screw in control cable (4) up to halfway point of thread.

11

Pull out sliding door emergency release (1) with electrical line (3) and detach cord from electrical line (3)

 Cord serves as assembly aid.

12

Install in the reverse order

Learn in electric sliding door

13

Completely open sliding door with switch on center console and close again



Check

14

Perform function test