ar4725d0018b

Empty drain line

Type ar · emne 47.25 · version 0101 · 2016-12-16

Gælder for: Engine 111.984 in model 902, 903, 904 with code KL9 (Underfloor gas pressure container) with code MY9 (Liquefied Gas Technology (LGT)) except code KL8 (Gas pressure container in load space)

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 47 Brændstofsystem, energiforsyning drivline › 47.25 Ledninger, slanger — Serie 902 · Serie 903 · Serie 904

EinPAS 16 Brændstof-/energiforsyning motor › 16.10 Brændstofforsyning › 16.10.13 ledning/slange/ventil — Serie 902 · Serie 903 · Serie 904

Gælder også for motorer/gearkasser: 111 984

AR47.25-D-0018B

Empty drain line

01.12.2016

Engine

111.984 in model 902, 903, 904

with code KL9 (Underfloor gas pressure container)

with code MY9 (Liquefied Gas Technology (LGT))

except code KL8 (Gas pressure container in load space)

Empty drain line

Shown on 65 liter gas reservoir

3

Gas reservoir holder

4

Gas cylinder

6

Electrical connection

8

Screw/bolt

9

Cover

11

Clamp

13

Rubber grommet

14

Manual valve

17

Protective grille

D47.25-1116-06

Danger !

Risk of explosion due to escaping combustible gas or overheating of gas cylinders.Risk of injury caused by burns to skin and eyes. Risk of frostbite to body parts caused by escaping gas and by touching components near the valves when emptying gas cylinders. Risk of poisoning or suffocation caused by inhaling gas.

Remove any sources of ignition.
Protective clothing, safety gloves and safety glasses must always be worn.
Ensure that the work area is adequately ventilated.
When working on vehicles at ambient temperatures over 60 °C, all gas cylinders must be removed.

AS00.00-Z-0018-01A

Danger !

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

Note on calculation of tightening torque when using insertion or socket tools with various effective lengths

AH00.00-P-0015-01CW

Discharge, fill

1

Push back rubber grommet (13) by about 20 cm

2

Remove clamp (11) at gas reservoir holder (3)

Bolt, pipe clamp to frame

*BA47.10-N-1007-02B

3

Remove protective grille (17)

4

Put on major assembly mount with support plate on gas reservoir (4), lash down and raise slightly

000 588 11 62 00 Major assembly mount

WS01.00-P-0092B

000 588 10 62 00 Support plate

WS26.00-P-3309B

5

Remove the gas reservoir (4) on gas reservoir holder (3)

Screw/bolt, gas reservoir to bracket

*BA47.10-N-1003-02B

6

Lower the gas reservoir (4) by about 30 cm

Installation: Ensure the mounting bolt is in the correct position.

7

Push back screws/bolts (8) and remove cover (9)

8

Close off manual valve (14)

9

Release and disconnect electrical connection (6) for solenoids

10

Set selection switch to the gas position

After selection switch the green diode lights up.

11

Start the engine and allow it to run with the vehicle stationary until the engine stops on its own.

Gas system is adequately emptied after engine OFF.

12

Fill in reverse order

Compressed-gas tank, gas shutoff valve

Number

Designation

Engine 111.984

BA47.10-N-1003-02B

Screw/bolt, gas reservoir to bracket

Nm

53

Compressed-gas tank, gas shutoff valve

Number

Designation

Engine 111.984

BA47.10-N-1007-02B

Bolt, pipe clamp to frame

Nm

10

Henviste dokumenter