ar4710d0001a

Remove/install bracket of front compressed-gas tanks

Type ar · emne 47.10 · version 0103 · 2004-04-15

Gælder for: MODELS 902.062 /072, 903.062 /063 /072 /073 with CODE (KL9) Compressed-gas tank underfloor arrangement with CODE (MS7) NGT (Natural Gas Transporter) sprinter without protective grille MODELS 902.662 /672, 903.662 /663 /672 /673 with CODE (KL9) Compressed-gas tank underfloor arrangement with CODE (MS7) NGT (Natural Gas Transporter) sprinter with protective grille

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 47 Brændstofsystem, energiforsyning drivline › 47.10 Brændstoftank — Serie 902 (modeller 062, 072, 662, 672) · Serie 903 (modeller 062, 063, 072, 073, 662, 663, 672, 673)

EinPAS 16 Brændstof-/energiforsyning motor › 16.10 Brændstofforsyning › 16.10.40 brændstoftank/påfyldningsanordning — Serie 902 (modeller 062, 072, 662, 672) · Serie 903 (modeller 062, 063, 072, 073, 662, 663, 672, 673)

AR47.10-D-0001A

Remove/install bracket of front compressed-gas tanks

30.6.98

MODELS 902.062 /072, 903.062 /063 /072 /073
with CODE (KL9) Compressed-gas tank underfloor arrangement
with CODE (MS7) NGT (Natural Gas Transporter) sprinter
without protective grille

MODELS 902.662 /672, 903.662 /663 /672 /673
with CODE (KL9) Compressed-gas tank underfloor arrangement
with CODE (MS7) NGT (Natural Gas Transporter) sprinter
with protective grille

Remove/install bracket of front compressed-gas tanks

D47.10-1101-09

1 Bracket of compressed-gas tanks

2 Washer

3 Hexagon nut

6 Protective grille
(only for appropriate version)

7 Hexagon bolt

4 Hexagon bolt

5 High-pressure line (to distributor block)

Remove/Install

Danger!

Risk of explosion. When working on natural-gas vehicles, escaping natural gas or an overheated compressed-gas tank may result in explosion. Risk of frostbite to body parts from escaping natural gas or contact with components near the valves hile while draining compressed-gas tanks. Risk of poisoning or risk of suffocation from inhaling natural gas.

Remove any sources of ignition.

Ensure that the work area is adequately ventilated.

Wear heat-protective gloves.

AS00.00-Z-0018-01A

1

Close gas shutoff valves at compressed-gas tanks

AR47.10-D-0005A

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns while working in the engine during the starting procedure or when the engine is running

Secure vehicle to prevent it from starting on its own.
Wear closed and snug-fitting work clothes.
Do not grasp hot or rotating parts.

AS00.00-Z-0005-01A

2

Start the engine and allow it to run with the vehicle stationary until the engine stops on its own.

Push extraction hose onto exhaust pipe. After engine has stopped, switch ignition off. Gas system is adequately emptied after engine stops.

3

Remove protective grille (6)

Only if fitted.

4

Detach the high-pressure line (5) to the distributor block from the first compressed-gas tank

Installation: Tighten the threaded connection of the pipe as instructed.

AR47.25-D-0005A

5

Detach the bracket (1) completely with compressed-gas tanks

6

Install in the reverse order

7

Check the high pressure line connection (5) for leaks

Moisten the entire connection with suds and check the formation of bubbles

Henviste dokumenter