ar4230p0160gh

Remove/install ABS measuring ring

Type ar · emne 42.30 · version 0110 · 2020-02-04

Gælder for: Model 461 with rear axle 741.171/52/53 Model 463 (except 463.270/271) with rear axle 748 up to model year 2013

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 42 Bremsehydraulik og -mekanik › 42.30 Antiblokeringssystem (ABS) — Serie 461 · Serie 463 (modeller 200, 202, 204, 206, 207, 208, 209, 210, 215, 218, 220, 221, 222, 224, 225, 227, 228, 230, 231, 232, 233, 234, 235, 236, 237, 238, 239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 254, 255, 260, 261, 272, 273, 274, 275, 276, 277, 280, 300, 303, 304, 306, 307, 308, 309, 315, 318, 320, 321, 322, 323, 324, 325, 327, 328, 330, 331, 332, 333, 335, 336, 338, 340, 341, 342, 343, 346, 348, 349, 350)

EinPAS 26 Aktive sikkerhedssystemer › 26.20 Bremse-/traktionsregulering › 26.20.12 Sensor/kontakt/ledningssæt — Serie 461 · Serie 463 (modeller 200, 202, 204, 206, 207, 208, 209, 210, 215, 218, 220, 221, 222, 224, 225, 227, 228, 230, 231, 232, 233, 234, 235, 236, 237, 238, 239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 254, 255, 260, 261, 272, 273, 274, 275, 276, 277, 280, 300, 303, 304, 306, 307, 308, 309, 315, 318, 320, 321, 322, 323, 324, 325, 327, 328, 330, 331, 332, 333, 335, 336, 338, 340, 341, 342, 343, 346, 348, 349, 350)

Gælder også for motorer/gearkasser: 741 171, 741 52*, 741 53*, 748 ***

AR42.30-P-0160GH

Remove/install ABS measuring ring

03.02.2020

Model

461 with rear axle 741.171/52/53

Model

463 (except 463.270/271) with rear axle 748

up to model year 2013

Remove/install ABS measuring ring

1

Measuring ring for anti-lock braking system (ABS)

2

Drive shaft

P42.30-0321-01

Remove/install

1

Disassemble drive shaft (2) on front axle


Model 461 (except 461.331) with rear axle 741.171/52/53
Model 463 (except 463.270/271) with rear axle 748
up to model year 2013
except code ZQ0 (G 500 4x42)

AR33.30-P-0700A

Model 461.331 with rear axle 741.171/53

AR33.30-P-0700GX

2

Clamp drive shaft (2) into place

3

Grind down ABS measuring ring (1) using straight grinder to 2 mm then separate using chisel (arrow)


Do not damage axle shaft (2).
Otherwise, the ABS measuring ring (1) may not be correctly seated.

4

Press on new ABS measuring ring (1)

Heat up ABS measuring ring (1) to approx. 80 °C then press on using a suitable tool.

5

Install in the reverse order

Henviste dokumenter