Test values for distance and comparison measurements on rear axle
Number | Designation | Model | Model | |||
BE40.30-N-1001-05D | Test value | H1 | Effective dimension | mm | 2107 (2) | 2107 (2) |
max. difference left - right | mm | 4 | 4 | |||
H2 | Effective dimension | mm | 1760 (2) | 1760 (2) | ||
max. difference left - right | mm | 4 | 4 | |||
H3 | Effective dimension | mm | 1564 (2) | 1564 (2) | ||
max. difference left - right | mm | 3 | 3 | |||
H4 | Effective dimension | mm | 1026 (2) | 1026 (2) | ||
max. difference left - right | mm | 4 | 4 | |||
H5 | Effective dimension | mm | 635 (2) | 635 (2) | ||
max. difference left - right | mm | 3 | 3 | |||
H6 | Effective dimension | mm | 872 (2) | 1007 (2) | ||
max. difference left - right | mm | 4 | 4 | |||
See picture | ||||||
BE40.30-N-1002-05D | Test value | H7 | Effective dimension | mm | 136 (2) | 521 (2) |
max. difference left - right | mm | 3 | 3 | |||
H8 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
H9 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
H10 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
H11 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
See picture | ||||||
Test values for distance and comparison measurements on rear axle
Number | Designation | Model | Model | |||
BE40.30-N-1001-05D | Test value | H1 | Effective dimension | mm | 2107 (2) | 2107 (2) |
max. difference left - right | mm | 4 | 4 | |||
H2 | Effective dimension | mm | 1760 (2) | 1760 (2) | ||
max. difference left - right | mm | 4 | 4 | |||
H3 | Effective dimension | mm | 1564 (2) | 1564 (2) | ||
max. difference left - right | mm | 3 | 3 | |||
H4 | Effective dimension | mm | 1026 (2) | 1026 (2) | ||
max. difference left - right | mm | 4 | 4 | |||
H5 | Effective dimension | mm | 635 (2) | 635 (2) | ||
max. difference left - right | mm | 3 | 3 | |||
H6 | Effective dimension | mm | 872 (2) | 1007 (2) | ||
max. difference left - right | mm | 4 | 4 | |||
See picture | ||||||
BE40.30-N-1002-05D | Test value | H7 | Effective dimension | mm | 136 (2) | 521 (2) |
max. difference left - right | mm | 3 | 3 | |||
H8 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
H9 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
H10 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
H11 | Effective dimension | mm | - | - | ||
max. difference left - right | mm | - | - | |||
See picture | ||||||
Frame test values
Number | Designation | Model | Model | |||
BE40.30-N-1001-09C | Frame width test value | BR1 | Effective dimension | mm | 925 (2) | 925 (2) |
Distance of inner side of side rails from one another | 851 (2) | 851 (2) | ||||
BR2 | Effective dimension | mm | 703 (2) | 703 (2) | ||
Distance of inner side of side rails from one another | 636 (2) | 636 (2) | ||||
See picture | ||||||
- | ||||||
Anti-roll bar
Number | Designation | Model | Model | Model | ||
BA32.35-N-1001-03B | Screw, connecting rod to stabilizer and longitudinal frame member (rear axle) | M121.5 | Nm | 106 | 106 | - |
M12 | Nm | - | - | 104 | ||
Adapter
906 589 09 63 00
D40.30-1105-08
D40.30-1117-11
The beam trammel for measuring of the vehicle frame is made up of the following tools:
- Contact arm (01)
- Measuring cone (02)
- Measuring tips (400 mm) (03)
- Adapter (04)
- Beam trammel (05)
Beam trammel
gotis://K_60-65_01.0
D40.30-1110-01
1 Measure reference dimension (H1) from check point (K) to check point (k3) on longitudinal member.
To do so, use contact arm (01) for check point (K). Measure to left side and right side in each case. If a screw is not screwed in to locate the contact arm (01) in the weld nut, screw a suitable bolt (M1030) from the interior into the weld nut.
D40.30-1113-01
D40.30-1116-01
2 Measure reference dimension (H2) from check point (k3) on longitudinal member to check point (k4) on longitudinal member located opposite.
Measure on left side and right side in each case.
D40.30-1126-01
D40.30-1114-01
3 Measure reference dimension (H3) from check point (k3) on longitudinal member to check point (k4) on longitudinal member.
Measure on left side and right side in each case.
D40.30-1126-01
For correct measurement it may be necessary to detach the link rod (2) for the torsion bar on the frame.
D40.30-1120-01
4 Measure reference dimension "H4" from check point (k4) on longitudinal member to check point (k5) on longitudinal member located opposite.
Measure on left side and right side in each case.
D40.30-1121-01
5 Measure reference dimension "H5" from check point (k4) on longitudinal member to check point (k5) on longitudinal member.
Measure on left side and right side in each case.
D40.30-1122-01
6 Measure reference dimension "H6" from check point (k5) on longitudinal member to check point (k6) on longitudinal member located opposite.
To do so use adapter (04) for the check point (k6). Measure on left side and right side in each case. If a step or trailer hitch, is mounted, turn the adapter (04) over and then use it.
D40.30-1123-01
7 Measure reference dimension "H7" from check point (k5) on longitudinal member to check point (k6) on longitudinal member.
To do so use adapter (04) for the check point (k6). Measure on left side and right side in each case. If the tow hook is mounted for better locking of the adapter (04), insert suitable collar bolt with shim (for height adjustment) into the upper bore and secure using a nut.
If a step or trailer hitch, is mounted, turn the adapter (04) over and then use it.