Check vehicle level at front and rear axles using electronic inclinometer

AR40.20-S-0302E

Check vehicle level at front and rear axles using electronic inclinometer

27.02.2020

Model

447, 448

Shown on vehicle with front wheel drive or all-wheel drive on front axle

1

Front axle shaft

4

Measuring sensor

Shown on vehicle with rear wheel drive on front axle

3

Transverse control arm

4

Measuring sensor

Shown on vehicle with rear wheel drive or all-wheel drive on rear axle

4

Measuring sensor

5

Rear axle shaft

Shown on vehicle with front wheel drive on rear axle

2

Semi-trailing arm

4

Measuring sensor

6

Menu item

7

Inclination meter



Check

1

Observe general information on chassis alignment

AR40.20-S-0201E



Clean

2.1

Clean measuring points on rear axle shafts (5) and transverse control arms (3)

Model 447 with engine 651, 654.9
except code ZG2 (Permanent all-wheel drive)
Model 447, 448 with engine 274


The measuring points must be clean and free of residue.
Otherwise, measurement errors may occur.

2.2

Clean measuring points on front axle shafts (1) and rear axle shafts (5)

Model 447 with engine 651, 654.9
with code ZG2 (Permanent all-wheel drive)


The measuring points must be clean and free of residue.
Otherwise, measurement errors may occur.

2.3

Clean measuring points on front axle shafts (1) and semi-trailing arms (2)

Model 447 with engine 622, 780


The measuring points must be clean and free of residue.
Otherwise, measurement errors may occur.



Measure

3

Select menu item (6) in inclinometer (7)



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B

4.1

Place measuring sensor (4) on front left axle shaft (1) and save measured value

Model 447 with engine 622, 780
Model 447 with engine 651, 654.9
with code ZG2 (Permanent all-wheel drive)



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face the center of the vehicle.
Otherwise measurement errors will occur.

4.2

Place measuring sensor (4) on left transverse control arm (3) and save measured value

Model 447 with engine 651, 654.9
except code ZG2 (Permanent all-wheel drive)
Model 447, 448 with engine 274



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face the center of the vehicle.
Otherwise measurement errors will occur.

5.1

Place measuring sensor (4) on front right axle shaft (1) and save measured value

Model 447 with engine 622, 780
Model 447 with engine 651, 654.9
with code ZG2 (Permanent all-wheel drive)



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face the center of the vehicle.
Otherwise measurement errors will occur.

5.2

Place measuring sensor (4) on right transverse control arm (3) and save measured value

Model 447 with engine 651, 654.9
except code ZG2 (Permanent all-wheel drive)
Model 447, 448 with engine 274



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face the center of the vehicle.
Otherwise measurement errors will occur.

6.1

Place measuring sensor (4) on rear left axle shaft (5) and save measured value

Model 447 with engine 651, 654.9
Model 447, 448 with engine 274



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face the center of the vehicle.
Otherwise measurement errors will occur.

6.2

Place measuring sensor (4) on left semi-trailing arm (2) and save measured value

Model 447 with engine 622, 780



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face towards the rear.
Otherwise measurement errors will occur.

7.1

Place measuring sensor (4) on rear right axle shaft (5) and save measured value

Model 447 with engine 651, 654.9
Model 447, 448 with engine 274



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face the center of the vehicle.
Otherwise measurement errors will occur.

7.2

Place measuring sensor (4) on right semi-trailing arm (2) and save measured value

Model 447 with engine 622, 780



000 588 05 19 00 Vehicle level inclinometer

WS40.00-P-0007B


The connecting cable of the measuring sensor (4) must face towards the rear.
Otherwise measurement errors will occur.