ar3531p055028ca

Attaching end cover

Type ar · emne 35.31 · version 0121 · 2010-03-08

Gælder for: MODEL 170.444 /445 /447 /449, 202.087 /088 /089 /188, 208.335 /344 /345 /347 /348 /435 /444 /445 /447 /448, 210.010 /020 /035 /037 /048 /061 /062 /210 /235 /237 /248 /261 /262 /610Rear axle center assembly dia. 185 MODEL 202.078, 210.003 /004Rear axle center assembly dia. 185 with CODE (450) Taxi version MODEL 202.194, 210.007Rear axle center assembly dia. 185 except CODE (450) Taxi version

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 35 Bagaksel › 35.31 Bagakselmidtersamling — Serie 170 (modeller 444, 445, 447, 449) · Serie 202 (modeller 078, 087, 088, 089, 188, 194) · Serie 208 (modeller 335, 344, 345, 347, 348, 435, 444, 445, 447, 448) · Serie 210 (modeller 003, 004, 007, 010, 020, 035, 037, 048, 061, 062, 210, 235, 237, 248, 261, 262, 610)

EinPAS 17 Drivstreng/aksel › 17.51 Bagaksel › 17.51.65 differentiale/akselkraftgennemføring — Serie 170 (modeller 444, 445, 447, 449) · Serie 202 (modeller 078, 087, 088, 089, 188, 194) · Serie 208 (modeller 335, 344, 345, 347, 348, 435, 444, 445, 447, 448) · Serie 210 (modeller 003, 004, 007, 010, 020, 035, 037, 048, 061, 062, 210, 235, 237, 248, 261, 262, 610)

AR35.31-P-0550-28CA

Attaching end cover

Rear axle differential end cover with non-machined sealing surface

Model 170, 202, 208, 210

BT35.31-P-0014-01A

Rear axle center assembly housing

Number

Designation

Model
170

Model
202

BA35.31-P-1001-02A

Bolt, end cover to rear axle differential

Bolt+washer

Nm

-

50

Flange bolt
(TORX, internal serrations)

Stage 1

Nm

30

30

Stage 2

°

45

45

Rear axle center assembly housing

Number

Designation

Model
208

Model
210

BA35.31-P-1001-02A

Bolt, end cover to rear axle differential

Bolt+washer

Nm

-

50

Flange bolt
(TORX, internal serrations)

Stage 1

Nm

30

30

Stage 2

°

45

45

Attaching end cover
Attaching end cover

001 589 66 21 00

Torque wrench

Squeeze gun

112 589 00 25 00

Repair materials

Number

Designation

Order number

BR00.45-Z-1013-01A

Loctite sealant 5970

A 003 989 98 20

Attaching end cover

P35.31-2039-10

1 Clean machined sealing surface (a) or unmachined sealing surface (b) on the old end cover (A) or new end cover (B) as well as the sealing surface on the rear axle differential housing.
All sealing surfaces must be free of oil and grease.

A Used end cover

B New end cover

a Machined sealing surface

b Unmachined sealing surface

c Groove (projection)

Attaching end cover

P35.31-2038-01

2 Apply sealing compound around circumference of sealing surface (arrow).
The sealing compound must be applied only to the specified sealing surfaces (arrow) with a bead of 2.0 mm (0.5 mm). The sealing compound must be applied within 10 min. The silicone bead should not be spread. Only the approved sealant may be used.

Attaching end cover

P35.31-2205-10

Use flange bolts.

3 Position the end cover (54) and secure with flange bolts.
The end cover (54) must not slip.

4 Tighten the flange bolts with torque wrench to stage 1 .

5 Mark bolt flanges relative to rear axle differential housing (d).

6 Place mark (e) on rear axle differential offset by 45°.

7 Tighten flange bolts with 45° tightening angle as per stage 2.
The markings (d, e) should coincide The tightening angle can also be checked using a commercially available angle tester.

Henviste dokumenter