Remove/install center drive shaft with bearing · ar3330s7706m · Mercedes-Benz WIS

AR33.30-S-7706M

Remove/install center drive shaft with bearing

12.2.97

MODEL 638 with ENGINE 111.948 /950 /978 /980, 601.942 /970

Remove/install center drive shaft with bearing

S33.30-2507-09

1 Center driveshaft

2 Bearing

3 Rubber ring (manual transmission)

7 Retaining screw

8 Stationary engine support

9 Drive shaft

4 Circlip

5 O-ring (on automatic transmission only)

6 Spring pin

	Remove
1	Disconnect right drive shaft (9) from center drive shaft (1)	 Tie back drive shaft (9).	AR33.30-S-6500M
2	Remove brake caliper	 Do not disconnect the brake hose, but push it to one side so that it does not interfere with work.	AR42.10-S-0070A
3	Unscrew nuts on left and right struts of anti-roll bar	 Turn up anti-roll bar.
4	Drain transmission oil	 without code G40 (manual transmission)	AP26.00-D-2601A
		 with code G40 (automatic transmission)	AP27.00-D-2701A
5	Pull off center drive shaft		AR33.30-S-7706-01A
		 Puller	*638589013300
6	Remove spring pin (4) from center drive shaft (1)
7	Pull out rubber ring (3)
8	Remove center drive shaft (1)	 Turn the steering to the right until the center drive shaft can be pulled out.
9	Remove ball bearing (2)	 Only when replacing the center drive shaft or bearing.  If the ball bearing (2) remains on the center drive shaft 
		 Puller	*638589023300
		 If the ball bearing (2) remains on the fixed engine support 
		 Puller Ø 28-37 mm	*000589283300
		 Countersupport	*631589133300
	Install
10	Install ball bearing (2) for center drive shaft with the aid of the tool	 Drift	*638589031500
11	Install center drive shaft (1) in fixed engine support (8)
12	Install rubber ring (3)
13	Fit snap ring (4) on center drive shaft (1)
14	Install center drive shaft (1) using the tool	 The snap ring (4) should engage in the transmission housing.	AR33.30-S-7706-01A
		 Puller	*638589013300
15	Tighten nuts on left and right struts of anti-roll bar	 Replace self-locking nut.
		 Turn up anti-roll bar.
			*BA32.35-N-1001-02B
16	Install brake caliper		AR42.10-S-0070A
17	Connect right drive shaft (9) to center drive shaft (1)		AR33.30-S-6500M
18	Fill transmission with oil	 without code G40 (manual transmission)	AP26.00-D-2601A
		 with code G40 (automatic transmission)	AP27.00-D-2701A
	Check
19	Check for leaks

 Front axle anti-roll bar

Number	Designation		Model 638


BA32.35-N-1001-02B	Mounting of anti-roll bar to strut of shock absorber	Nm	62

638 589 02 33 00

000 589 28 33 00

638 589 03 15 00

638 589 01 33 00

Puller

Drift

Puller, dia. 28-37 mm

631 589 13 33 00

Countersupport

Henviste dokumenter

ap2600d2601a Manuel gearkasse - olieskift
ap2700d2701a
ar3330s6500m Drivaksler af-, påmontering
ar3330s770601a Mellemste drivaksel af-, påmonteres
ar4210s0070a