W18.20-1025-09
1 | Oil filter cover | 6 | Bracket | 11 | Charge air pipe | ||
2 | Oil filter housing | 7 | Carrier with guide pulley | 12 | Poly-V-belt | ||
3 | Seal | 8 | Coolant line | 13 | Guide pulley | ||
4 | Oil pressure line | 9 | Bracket | 14 | Poly-V belt tensioning device | ||
5 | Coolant line (only in vehicles with code MS4 (BlueTec 4) or code MS5 (BlueTec 5)) | 10 | Air intake pipe | 15 | Alternator carrier |
| Remove/install | ||
1 | Remove charge air pipe (11) from charge air cooler to charge air manifold | ||
2 | Remove air intake pipe (10) | ||
3 | Remove bracket (9) at coolant pump and push away with coolant line (8) | Bracket to coolant pump | |
4 | Unscrew oil filter cover (1) from oil filter housing (2) and remove | When oil filter cover (1) is pulled out, engine oil will flow back into oil pan from oil filter housing (2). | |
Installation: Replace sealing ring. | |||
Oil filter cover to oil filter housing | |||
5 | Remove oil pressure line (4) at oil filter housing (2) | Collect escaping engine oil, seal oil holes. | |
Installation: Install new sealing rings. | |||
6 | Swivel tensioner pulley of poly-V belt tensioning device (14) downward and take off poly-V belt (12) at guide pulley (13) | ||
| |||
Observe poly-V belt (12) routing diagram. | |||
Installation: Check condition of poly-V belt (12); replace if necessary. | |||
7 | Remove guide pulley (13) at oil filter housing (2) | Bolt, guide pulley to oil filter | |
8 | Remove carrier with guide pulley (7) on bracket (6) | Bolt, guide pulley carrier to holder | |
9 | Remove bracket (6) at oil filter housing (2) | Bolt, holder to oil filter | |
10 | Detach carrier with guide pulley (7) at alternator carrier (15) | Bolt, guide pulley carrier to alternator carrier | |
11 | Disconnect electrical connection at oil pressure and oil temperature combination sensor | Only for engine 926.9 up to engine end no. 301561. | |
12 | Remove bracket for coolant line (5) at oil filter housing (2) | Only in vehicles with code MS4 (BlueTec 4) or code MS5 (BlueTec 5). | |
Bolt, oil filter housing to crankcase | |||
13 | Remove oil filter housing (2) from cylinder crankcase | Bolt, oil filter housing to crankcase | |
14 | Remove seal (3) | Installation: Replace seal (3). | |
15 | Install in the reverse order | ||
16 | Check engine oil level on display or with oil dipstick; add oil if necessary | ||
Notes on engine oil | |||
Observe engine oil grade set in maintenance system or Specifications for Operating Fluids. | |||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
17 | Start engine and allow to run in idle for 10 s until the oil pressure has built up, then run the engine at varying speeds | ||
18 | Switch off engine and check seal in area around oil filter | Visual inspection. |
Henviste dokumenter
- ah1800n010101ha Oplysninger om motorolie
- ap1322d135101a Skadesbilleder for kilerem
- ar0910w8131jb
- ar0941w1311jd
- ar1322w390202d
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører