Remove/install right oxygen sensor upstream of catalytic converter

AR07.04-P-0083LFB

Remove/install right oxygen sensor upstream of catalytic converter

28.07.2016

Engine

157, 278 in model 217, 222

Shown on model 217 with engine 278

1

Right oxygen sensor upstream of catalytic converter

2

Electrical line

3

Bracket

4

Bracket

5

Electrical connection

 Danger !

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

 Danger !

Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.

Wear protective gloves, protective clothing and safety glasses, if necessary.

AS00.00-Z-0002-01A



Notes on avoiding damage through contamination and foreign objects

AH00.00-P-5000-01A



Remove

1

Switch off ignition and store transmitter key outside of transmission range (min. 2 m)

2

Remove rear center and middle lower engine compartment paneling

AR61.20-P-1105LF

3

Unclip electrical line (2) from the bracket (3)

4

Unclip electrical connection (5) from the bracket (4)

5

Release and disconnect electrical connection (5)

6

Remove right oxygen sensor upstream of catalytic converter (1)

 Box wrench bit

*000589710300

7

Cover sensor tip of the right oxygen sensor upstream of CAT (1) with protective cover

For reuse of the right oxygen sensor upstream of CAT (1).

 Set of protective caps

*001589009100

8

Close off threaded hole of right oxygen sensor upstream of CAT (1)

 Commercially available devices/tools
Oxygen sensor screw plug threaded hole M18x1.5 mm



Install

9

Remove protective cover from sensor tip of the right oxygen sensor upstream CAT (1)

For reuse of the right oxygen sensor upstream of CAT (1).

 Set of protective caps

*001589009100

10

Coat thread of the right oxygen sensor upstream of catalytic converter (1) with heat-resistant lubricant

For reuse of the right oxygen sensor upstream of CAT (1).

Paste, hot lubrication 1 kg, DBL 6879.20

*BR00.45-Z-1005-06A

11

Remove screw plug from threaded hole of the right oxygen sensor upstream of CAT (1)

 Commercially available devices/tools
Oxygen sensor screw plug threaded hole M18x1.5 mm

12

Screw in right oxygen sensor upstream of catalytic converter (1)



Note on calculation of tightening torque when using insertion or socket tools with various effective lengths

AH00.00-P-0015-01CW

 Oxygen sensor to catalytic converter

*BA14.00-P-1002-01A

 Box wrench bit

*000589710300

13

Clip electrical line (2) into the holder (3)

14

Plug together electrical connection (5) until it locks

15

Clip electrical connection (5) into the holder (4)



Check

 Danger !

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

16

Carry out an engine test run and check exhaust system for leaktightness

17

Install lower rear and center engine compartment paneling

AR61.20-P-1105LF

18

Read out fault memory using the diagnostic system and clear if necessary



AD00.00-P-2000-04B

 Oxygen sensor

Number

Designation

Engine 157, 278

BA14.00-P-1002-01A

Oxygen sensor to catalytic converter

Nm

50

Repair materials

Number

Designation

Order number

BR00.45-Z-1005-06A

Paste, hot lubrication 1 kg, DBL 6879.20

A 000 989 76 51