Checking and machining valves · ar0530p4201hw · Mercedes-Benz WIS

AR05.30-P-4201HW

Checking and machining valves

31.10.97

ENGINE 601, 602, 603 (except 602.982)

P01.30-0310-09

 	Removing, installing
1	Remove cylinder head		AR01.30-P-5800HX
2	Remove valve springs and valve stem seals		AR05.30-D-3510-02A
			*603589014000
			*111589256100
			*601589015900
			*606589003700
3	Remove valves
	Inspecting
4	Clean valves and carry out a visual inspection	 Valves with scorched valve disk, with insufficient height (h) of valve disk or with used or scored valve stem, should be replaced.	*BE05.30-P-1002-01D
5	Measure concentricity at valve stem and valve seat	if necessary replace valve	*BE05.30-P-1009-01D
 Danger!	Risk of explosion and poisoning from melting down and improper handling of sodium-filled valves. Risk of injury from burns and caustic burns to skin sections in the event of contact with sodium.	Do not open sodium-filled valves; if necessary, wear protective gloves and eye protection if valves are damaged.	AS05.30-Z-0001-01A
	Disposing of sodium-filled valves	in the case of exhaust valves with sodium filling	OS05.30-P-0001-01A
			*BE05.30-P-1006-01D
	Machining
6	Machine valve seat		*WE58.40-Z-1008-21A
		 Pay attention to operating instructions of machining equipment and to setting angle	*BE05.30-P-1008-01D
			*BE05.30-P-1003-01D
			*BE05.30-P-1002-01D
			*BE05.30-P-1001-01D
			*BE05.30-P-1004-01D
			*BE05.30-P-1005-01D
			*BE05.30-P-1006-01D
			*BE05.30-P-1007-01D
7	Once again measure runout at valve stem and valve seat	 If runout excessive or height (h) insufficient, replace valve	*BE05.30-P-1009-01D
8	Measure valve setback to cylinder head	refer to machining cylinder head contact surface if necessary 	ra01006010418x
		Inspecting, removing, installing valve guides	ra05006010291x
9	Insert valve, inspect for leaks		*WH58.30-Z-1012-05A
10	Install in the reverse order

Inspection data of valves

Number	Designation			Engine 601, 602.91, 603.91	Engine 602.96, 603.96


BE05.30-P-1001-01D	Valve disk dia. (D)	Exhaust	mm	34.90-35.10	34.90-35.10
		inlet	mm	37.90-38.10	37.90-38.10
		See figure		AR05.30-P-4201HW	AR05.30-P-4201HW
BE05.30-P-1002-01D	Height of valve disk (h)	Exhaust when new	mm	1.75-2.05	1.75-2.05
		Exhaust limit value	mm	1.6	1.6
		Inlet when new	mm	1.75-2.05	1.75-2.05
		Inlet limit value	mm	1.6	1.6
		See figure		AR05.30-P-4201HW	AR05.30-P-4201HW
BE05.30-P-1003-01D	Valve seat angle (α)	Exhaust	°	45° +15'	45° +15'
		inlet	°	45° +15'	45° +15'
		See figure		AR05.30-P-4201HW	AR05.30-P-4201HW
BE05.30-P-1004-01D	Valve stem Ø (D 1)	Exhaust	mm	8.945-8.960	8.945-8.960
		inlet	mm	7.955-7.970	7.955-7.970
		See figure		AR05.30-P-4201HW	AR05.30-P-4201HW
BE05.30-P-1005-01D	Valve seat armor plating without  1 with  2	Exhaust		2	2
		inlet		2	2
BE05.30-P-1006-01D	Sodium filling without  1 with  2	Exhaust		1	2
		inlet		1	2
BE05.30-P-1007-01D	Length of valve (L)	Exhaust standard	mm	106.4	106.4
		Exhaust repair size	mm	105.5	105.5
		Inlet standard	mm	106.4	106.4
		Inlet repair size	mm	105.5	105.5
		See figure		AR05.30-P-4201HW	AR05.30-P-4201HW
BE05.30-P-1008-01D	Width of valve seat	Exhaust	mm	2	2
		inlet	mm	2	2
BE05.30-P-1009-01D	Concentricity of valve seat to valve stem	Exhaust	mm	0.03	0.03
		inlet	mm	0.03	0.03
BE05.30-P-1010-01D	Identification on end of stem	Exhaust		A 601 05	E 601 15 or E 601 17
		Inlet		E 601 02	A 601 19 or A 601 23

601 589 01 59 00

Assembly board

111 589 25 61 00

Valve assembly tool case

603 589 01 40 00

Retaining wheel

Pliers

606 589 00 37 00

Commercially available tools

Number	Designation
WH58.30-Z-1012-05A	Vacuum testing unit

Workshop equipment

WE58.40-Z-1008-21A

Valve grinding machine

Henviste dokumenter

ar0130p5800hx
ar0530d351002a
as0530z000101a Eksplosionsfare og fare for forgiftning hvis natriumfyldte ventiler smelter eller behandles ukorrekt. Fare for personskade på grund af forbrænding og ætsning af hudområder ved kontakt med natrium.
os0530p000101a Bortskaffelse af natriumfyldte ventiler
ra01006010418x
ra05006010291x