ar0140s8930ps

Remove/install crankcase cover at transmission end with radial shaft sealing ring

Type ar · emne 01.40 · version 0300 · 2020-03-12

Gælder for: Engine 642 in model 470, 471

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 1 Motor › 01 Motor komplet, motorudluftning, topstykke, motorblok › 01.40 Motorblok, takthusdæksel, endedæksel — Serie 470 · Serie 471

EinPAS 15 Motor › 15.15 forbrændingsmotor komplet/motorblok/krumtapdrev › 15.15.31 motorblok/olieudskiller/udluftning — Serie 470 · Serie 471

Gælder også for motorer/gearkasser: 642 ***

AR01.40-S-8930PS

Remove/install crankcase cover at transmission end with radial shaft sealing ring

06.03.2020

Engine

642 in model 470, 471

Remove/install crankcase cover at transmission end with radial shaft sealing ring

1

Bolts

2

Bottom half of crankcase

3

Radial shaft sealing ring

4

Crankcase

5

Oil pan

S01.40-4530-82

Topical note

Notes on avoiding damage through contamination and foreign objects

AH00.00-P-5000-01A

Remove

1

Remove drive plate.

AR03.30-S-8003PS

2

Unscrew screw/bolts (1).

3

Heat crankcase cover (2).

000 588 00 84 00 Heat gun

WS54.00-P-0049B

4

Remove crankcase cover (2).

Clean

5

Remove residue of seal from sealing surfaces on crankcase (4) and oil pan (5).

AR01.00-P-0050-01A

Loctite 7200

*BR00.45-Z-1038-04A

Loctite 7063 (400 ml) cleaning spray

*BR00.45-Z-1046-04A

Install

6

Install new crankcase cover (2) with radial shaft sealing ring (3) and tighten screws (1).

AR01.40-S-8925-01PS

The geometry and condition have changed as compared to the crankcase cover (2) with radial shaft sealing ring (3) installed at the factory. If a steel crankcase cover (2) was installed previously, new screws with a shank length of 20 mm must be used.

Bolt, crankcase cover at rear to crankcase

*BA01.40-N-1001-01S

Sealant, Loctite 5970, 50 ml

*BR00.45-Z-1013-01A

Assembly cleaner

*BR00.45-Z-1028-04A

Loctite 7200

*BR00.45-Z-1038-04A

Application gun

*112589002500

Installation tool

*271589004300

7

Install drive plate.

AR03.30-S-8003PS

Only install lower engine compartment paneling after leak test.

8

Check and correct engine oil level.

AP18.00-S-0101PS

Warning

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

9

Perform engine test run and check engine for leak tightness.

10

Install lower engine compartment lining.

AR61.20-S-1105P

Crankcase, timing case cover, bottom half of crankcase

Number

Designation

Engine 642 in model 470, 471

BA01.40-N-1001-01S

Bolt, crankcase cover at rear to crankcase

Stage 1

Nm

8

Stage 2

Nm

10

Remove/install crankcase cover at transmission end with radial shaft sealing ring
Remove/install crankcase cover at transmission end with radial shaft sealing ring

271 589 00 43 00

Installation tool

112 589 00 25 00

Application gun

Repair materials

Number

Designation

Order number

BR00.45-Z-1013-01A

Sealant, Loctite 5970, 50 ml

A 003 989 98 20 10

BR00.45-Z-1028-04A

Assembly cleaner

A 000 986 56 01

BR00.45-Z-1038-04A

Loctite 7200

Henkel AG & Co. KGaA
http://www.loctite.de

BR00.45-Z-1046-04A

Loctite 7063 (400 ml) cleaning spray

A 001 986 71 71 09

Henviste dokumenter