Retrofit Common Telematics Platform (CTP) control unit

AN82.85-W-0108F

Retrofit Common Telematics Platform (CTP) control unit

11.10.2018

Model

963, 964

with code J9N (Pre-installation for Truck Data Center 6 (DTCO))

except code J9C (Pre-installation for FleetBoard for JADE)

except code J9O (Pre-install.for Truck Data Center 6 (FB Card))

Modification notes

12.06.2018

"Carry out parameterization of affected control units using data storage medium and the attached instructions", added.

Operation step 35

12.06.2018

Part number added.

Parts ordering note

11.10.2018

Data storage medium (purchase order with vehicle identification number (VIN) and "code J3S" in the additional field), added.

Parts ordering note

Shown on MODEL 963

1

Cover

6

Cover

10

Cover

2

Side vent

7

Center console paneling

A9

Truck Control Center (TCC)

4

Center air vent

8

Right center vent

A12

Heating/ventilation control and operating unit

5

Center module

9

Cover

Shown on MODEL 963

11

Cover

A150

Common Telematics Platform (CTP) control unit

12

Antenna plug

A150 X1

Connector socket

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A



Remove

1

Remove bottom trim for instrument panel on front passenger side.



AR68.10-W-1502H

2.1

Remove folding table.

Vehicles with code D7V (Table on passenger side)



AR68.20-W-8305H

2.2

Remove cover (1).

Vehicles without code D7V (Table on passenger side)

 Work instructions have not yet been compiled for this version.

3

Remove side air vent (2).

4

Remove Truck Control Center (TCC) (A9).



AR82.60-W-7800H

5

Remove ventilation heating control and operating unit (A12).

6

Remove center air vent (4).

7

Remove bolts from center module (5) and pull center module (5) towards rear.



Model 963, 964 with code F2C (Floor variant, tunnel 320 mm)

AR68.10-W-1004HC



Model 963, 964 with code F2B (Floor variant, tunnel 170 mm)

AR68.10-W-1004HB



Model 963, 964 with code F2A (Floor variant, level floor)

AR68.10-W-1004HA

8

Unclip cover (6).

 Do not remove cover (6).

 Mounting wedge

*110589035900

9

Remove trim from center console (7).

10

Remove center air vent at right (8).

11

Remove trim (9).

12

Remove trim (10).

13

Remove cover (11).

14

Replace multifunction antenna.

Only on vehicles produced between 01.03.2017 and 31.05.2017.



AR82.62-W-8990A



Install

15

Retrofit subharness for Common Telematics Platform (CTP).

AN82.85-W-0107-01F

 Pliers

*352589023700

16

Install control unit for Common Telematics Platform (CTP) (A150).

 Check that the Common Telematics Platform (CTP) control unit (A150) is correctly latched into place.

17

Connect antenna plugs (12) to control unit for Common Telematics Platform (CTP) (A150).

 The antenna plugs (12) are placed ready in the wiring harness on the front passenger side.
Note color coding of antenna plugs (12).

18

Connect connector socket (A150 X1) at Common Telematics Platform (CTP) control unit (A150).

19

Install Service Call switch into a free switch panel and connect plug housing.

 The plug housing lies prepared in the device installation frame for the Truck Control Center (TCC) (A9).

20

Install cover (11).

21

Install trim (10).

22

Install trim (9).

23

Install center air vent at right (8).

24

Install center console trim (7).

25

Clip in cover (6).

26

Move center module (5) into installation position and screw in bolts.



Model 963, 964 with code F2C (Floor variant, tunnel 320 mm)

AR68.10-W-1004HC



Model 963,964 with code F2B (Floor variant, tunnel 170 mm)

AR68.10-W-1004HB



Model 963, 964 with code F2A (Floor variant, level floor)

AR68.10-W-1004HA

27

Install center air vent (4).

28

Install ventilation heating control and operating unit (A12).

29

Install Truck Control Center (TCC) (A9).



AR82.60-W-7800H

30

Install side air vent (2).

31.1

Install folding table.

Vehicles with code D7V (Table on passenger side)



AR68.20-W-8305H

31.2

Install cover (1).

Vehicles without code D7V (Table on passenger side)

 Work instructions have not yet been compiled for this version.

32

Install bottom trim for instrument panel on front passenger side.



AR68.10-W-1502H

33

Connect diagnostic system and start XENTRY.

34

Commission instrument cluster control unit (ICUC).

Only for vehicles up to manufacturing date 28.02.18

 The update procedure is completely menu-assisted under:
ICUC   instrument cluster (A1) 
Adaptations 
Initial startup 
Control module programming

35

Carry out parameterization of the affected control units using the data storage medium and the instructions.

36

End XENTRY and remove the diagnostic system.

37

Carry out FleetBoard commissioning online.

 http://www.fleetboard.com/activate

Update Vehicle Documentation (VeDoc)

38

Attach "Control unit for Common Telematics Platform (CTP) retrofitted as per AN82.85­W­0108F" note under field organization text to DG 82.

Parts ordering note

Part no.

Designation

Quantity

A 960 446 10 60

Parts kit for Common Telematics Platform (CTP)

1

A 000 827 75 59

Data storage medium (purchase order with vehicle identification number (VIN) and "code J3S" in the additional field)

1

A 005 820 30 75

Antenna

n. B.