ar8370w6000a

Removing and installing coolant circuit solenoid valve

Typ ar · téma 83.70 · verze 0105 · 2004-09-30

Platí pro: MODEL 950, 952, 953, 954 with BODY 942.899 with CODE (H64) Eberspächer D9W hot water auxiliary heater'

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 3 Nástavba › 83 Klimatizace › 83.70 Nezávislé topení, přídavné topení, přihřívač — Řada 942 (modely 899) · Řada 950 · Řada 952 · Řada 953 · Řada 954

EinPAS 39 Topení/větrání/chlazení › 39.25 Nezávislé topení/přídavné topení › 39.25.13 Potrubí/hadice/ventil — Řada 942 (modely 899) · Řada 950 · Řada 952 · Řada 953 · Řada 954

AR83.70-W-6000A

Removing and installing coolant circuit solenoid valve

23.5.96

MODEL 950, 952, 953, 954 with BODY 942.899 with CODE (H64) Eberspächer D9W hot water auxiliary heater

Removing and installing coolant circuit solenoid valve

W83.70-0014-06

1 Connector

2 Connector

3 Bayonet nut

4 Retaining plate

5 Coolant hose

6 Hose clamp

7 Connecting pipe

8 Coolant hose

9 Connecting pipe

10 Coolant hose

11 Connecting pipe

12 Solenoid valve

13 Tie strap

14 Nut

15 Washer

16 Screw

Remove/Install

Danger!

Risk of injury to skin and eyes suffering scalding from contact with hot coolant spray. Risk of poisoning from swallowing coolant.

Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage bottles.

Wear protective gloves, protective clothing and eye protection.

AS20.00-Z-0001-01A

1

Allow pressure in coolant circuit to escape

2

Disconnect ground lead from battery

Do not interrupt main battery current in heater mode or in the run-on phase.

Danger!

Risk of injury caused by body parts being jammed and crushed when tilting cab

Ensure that no one is within the tilting range of the cab during tilting. Always tilt the cab all the way to the end position and secure with the safety strut.

AS60.80-Z-0001-01A

3

Tilt cab

4

Detach electric plug (1) and remove plug (2) with bayonet nut (3) from retaining plate (4)

5

Separate cable strap (13)

6

Disconnect coolant hose (10)

*000589403700

7

Open hose clamp (6) of coolant hose (10) and detach coolant hose from connecting pipe (11)

Collect escaping coolant (approx. 0.7 l) in a clean vessel.

Installation:

After installing heater unit, pour escaped coolant back into the coolant circuit.

8

Disconnect coolant hoses (5) and (8) in same manner

9

Remove solenoid valve (12)

*BA83.70-N-1013-03A

10

Install in the reverse order

11

Check coolant hose connections for leaks

Danger!

Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit

Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation and wear protective gloves.

AS83.70-Z-0002-01A

12

Check function of stationary heater

AR83.70-W-5302-02B

Stationary heater unit

Number

Designation

Models
950, 952, 953, 954
with body 942.899
with (CODE H64) "Eberspächer D9W" heater

BA83.70-N-1013-03A

Bolt of solenoid valve to retaining plate

Nm

20

Removing and installing coolant circuit solenoid valve

000 589 40 37 00

Clamping device

Odkazované dokumenty