ar8370p117702a

Checking emission level with carbon dioxide tester

Typ ar · téma 83.70 · verze 0115 · 2006-07-26

Platí pro: MODEL 210.### ## up to 636643 with ENGINE 604, 605, 606 with CODE (228) Stationary heater Heizgerät Thermo Top S MODEL 210.### ## up to 672083 with ENGINE 104, 111, 112, 113, 119 with CODE (228) Stationary heater MODEL 461 with ENGINE 602.983 with CODE (H12) Auxiliary heater MODEL 463 as of 1.9.96 up to 30.11.00 with CODE (H12) Auxiliary heater MODEL 202 up to 31.5.97 mit nachträglich eingebauter Standheizung Thermo Top S MODEL 210.### ## up to 340566 with ENGINE 602.982 mit Zuheizer oder nachträ

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 3 Nástavba › 83 Klimatizace › 83.70 Nezávislé topení, přídavné topení, přihřívač — Řada 202 · Řada 210 · Řada 461 · Řada 463 · Řada 602 (modely 982, 983)

EinPAS 39 Topení/větrání/chlazení › 39.25 Nezávislé topení/přídavné topení › 39.25.47 Výfuková soustava — Řada 202 · Řada 210 · Řada 461 · Řada 463 · Řada 602 (modely 982, 983)

Platí také pro motory/převodovky: 104 ***, 111 ***, 112 ***, 113 ***, 119 ***, 604 ***, 605 ***, 606 ***

AR83.70-P-1177-02A

Checking emission level with carbon dioxide tester

Danger!

Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit

Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation or wear protective gloves.

AS83.70-Z-0002-01A

Thermo Top S heater unit test values

Number

Designation

Model 202

Model 210

Model 461

Model 463

BE83.70-P-1001-03A

CO2 value in exhaust gas (diesel)

Wide open throttle operation

vol %

9,5-12,0

9,5-12,0

9,5-12,0

9,5-12,0

BE83.70-P-1002-03A

CO2 value in exhaust gas (gasoline)

Wide open throttle operation

vol %

9,5-12,0

9,5-12,0

9,5-12,0

9,5-12,0

Commercially available tools

Number

Designation

WH58.30-Z-1008-13A

CO2-testing unit

Checking emission level with carbon dioxide tester

P83.70-0241-01

Observe operating instructions of the CO2 tester.

1 Operate stationary heater or heater booster.

2 Swivel CO2 tester vertically through 180o.

The protective cap of the valve must point downwards and the measuring fluid must run once completely through the equipment cavity.
This has to be carried out before any measurement.

Checking emission level with carbon dioxide tester

P83.70-0242-01

3 Move the CO2 tester into the design position again (with the valve upwards (arrow) and allow the measuring fluid to run back completely..

4 Remove the protective cap from the valve (arrow) and press the valve several times for venting.

Checking emission level with carbon dioxide tester

P83.70-0243-01

5 Position CO2 tester vertically in the area of the exhaust gas outlet and adjust the 0 point on the scale to the level of the measuring fluid.

Checking emission level with carbon dioxide tester

6 Insert emission sensor in the exhaust gas outlet.

7 Let heater of stationary heater or heater booster run under full load.

8 Press the rubber coupling piece of the emission sensor firmly on the valve of the CO2 tester and keep depressed throughout the entire measuring process.

Due to the pressure, the valve is pressed down at the same time and therefore the entrance to the measuring fluid is opened.

9 Operate the rubber bellows of the emission sensor 18 times with the free hand.

10 Rapidly relieve rubber coupling piece and thus the valve.

To prevent the gas specimen taken from escaping from the CO2 tester.

11 Swivel the CO2 tester through 180o for a total of four times in succession.

The measuring fluid must run completely through the equipment cavity once in each case.

12 Position the CO2 tester vertically (valve upwards).

13 Read off CO2 level in percent by volume from the display scale and compare to the specified values.

After the measuring fluid has settled.

14 Adjust CO2 level in exhaust if necessary.

P83.70-0244-03

Checking emission level with carbon dioxide tester

P83.70-0242-01

15 Switch off stationary heater or heater booster.

16 Remove emission sensor from CO2 tester and bleed the CO2 tester by pressing the valve (arrow) several times. Then fit the protective cap to the valve (arrow).

Perform at the end of each measuring process.

Odkazované dokumenty