ar8330s6520a

Remove/install fluid reservoir

Typ ar · téma 83.30 · verze 0114 · 2009-12-14

Platí pro: MODEL 638 with CODE (H06) Air conditioning

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 3 Nástavba › 83 Klimatizace › 83.30 Klimatizace — Řada 638

EinPAS 39 Topení/větrání/chlazení › 39.15 Klimatizace › 39.15.41 Kondenzátor/vysoušeč/plynový chladič — Řada 638

AR83.30-S-6520A

Remove/install fluid reservoir

30.11.09

MODEL 638 with CODE (H06) Air conditioning

Remove/install fluid reservoir

S83.30-2011-06

Picture shows engine 111.948/978, 601.942/970

1 Refrigerant line

2 Sealing ring

3 Sealing ring

4 Refrigerant line

5 Fluid reservoir

6 Clip

7 Screw

Remove/install fluid reservoir

S83.30-2520-06

Picture shows engine 104.900

1 Refrigerant line

4 Refrigerant line

5 Fluid reservoir

6 Clip

7 Screw

8 Grill

Remove/install fluid reservoir

Picture shows engine 111.950/980, 611.980

1 Refrigerant line

4 Refrigerant line

5 Fluid reservoir

6 Clamp

B119 Tempmatic refrigerant pressure sensor

B119.1 Tempmatic refrigerant pressure sensor connector

S83.30-4002-03

Remove/install

Danger!

Risk of explosion caused by welding or soldering work on closed air conditioning system. Risk of poisoning caused by inhaling overheated refrigerant vapors. Risk of injury to skin and eyes caused by contact with liquid refrigerant.

Never perform welding work on or near a closed air conditioning system. No smoking or open flames. Wear safety glasses and protective gloves. Work only in well ventilated areas. Carry out repair work on the air conditioning system circuit only after the system has been discharged.

AS83.00-Z-0001-01A

When working on the refrigerant circuit seal all openings using suitable covers to prevent any unnecessary ingress of air humidity and dirt.

All sealing rings must be replaced and moistened with compressor oil.

1

Switch off ignition

2

Discharge air conditioning system

AR83.30-S-1760A

3.1

Remove grill (8)

Only with engine 104.900

AR88.00-S-2115A

4.1

Remove air distributor

Only with engine 104.900

5.1

Remove screw (7)

Only with engine 111.948/978, 601.942/970 and 104.900

6.1

Unplug connector (B119.1)

Only with engine 111.950/980, 611.980

7

Detach refrigerant lines (1, 4) on fluid reservoir (5)

Installation: Replace sealing rings (2, 3), wet threaded stud and sealing rings (2, 3) using compressor oil.

*BA83.30-N-1003-01A

8

Use suitable plugs to seal refrigerant lines (1, 4)

9

Undo clamp (6), remove fluid reservoir (5)

In the event of any intervention to the air conditioning system the fluid reservoir (5) must be replaced.

*BF83.30-N-1005-01A

Observe oil refill quantity when replacing fluid reservoir (5).

10

Install in the reverse order

Checking

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury from bruises and burns if you place your hand into the engine when it is started or when it is running.

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

11

Check air conditioning for proper operation

Run engine at idling speed for about 4 minutes and check all the component functions which are of relevance for proper operation of the air conditioning system.

Air conditioning

Number

Designation

Model
638

BA83.30-N-1003-01A

High pressure lines to fluid reservoir

Nm

17

Air conditioning

Number

Designation

Model
638 with compressor 10PA17C

Model
638 with compressor 7SB16

BF83.30-N-1005-01A

Refill quantity of compressor oil when replacing the accumulator

cm3

10

10

Specifications for
Operating Fluids

Sheet

BB00.40-P-0362-00A

BB00.40-P-0362-00A

Air conditioning

Number

Designation

Model
638 with compressor SD7V16

BF83.30-N-1005-01A

Refill quantity of compressor oil when replacing the accumulator

cm3

10

Specifications for
Operating Fluids

Sheet

BB00.40-P-0362-00A

Odkazované dokumenty