P68.30-3170-09
Shown with code (810) Sound system
1 C-pillar paneling
2 Bolt
3 Belt end fitting
4 Edge guard
5 Clamps
H4/54 Left rear surround speaker
(with code (810) Sound system)
H4/57 Right rear surround speaker
(with code (810) Sound system)
9 Lug
11 Edge guard
12 Seat belt
13 Strip (with code (290) Windowbag)
15 Clip (not with code (290) Windowbag)
P68.30-3169-07
6 Cover
7 Trim ring
14 Plug clip
8 Side paneling
10 Clamps
| Remove/install | ||
1 | Put down left or right seat cushion of rear bench seat | ||
2 | Unscrew bolt (2) and remove belt end fitting (3) | | |
3 | Pivot back left or right rear bench seat backrest | ||
4 | Loosen edge guard (4) in upper area of C-pillar | Installation: Ensure that edge guard (4) is seated properly. | |
5 | Press C-pillar paneling (1) out of clips (5) with mounting wedge | Installation: Correctly arrest C-pillar paneling (1) in clips (5) | |
| |||
6.1 | Remove cover (6) | On vehicles with code (290) Windowbag | |
7.1 | Unclip rosette (7) | On vehicles with code (290) Windowbag | |
Rosette (7) is damaged during removal and must be replaced. | |||
| |||
8 | Open tailgate | ||
9 | Remove luggage compartment cover in trunk | ||
10.1 | Loosen side paneling (8) from C-pillar paneling (1) in upper area (arrows A). | On vehicles with code (290) Windowbag | |
10.2 | Loosen side paneling (8) in area of insert clip (14) until insert clip (14) is accessible. | On vehicles without code (290) Windowbag | |
11 | Remove plug clip (14) | ||
12.1 | Remove sidebag unit in rear | On vehicles with code (290) Windowbag and code (293) left and right sidebag in rear Do not separate electrical connection. | |
13.1 | Pull C-pillar paneling (1) toward rear in area of sidebag and install rear sidebag in mount behind C-pillar paneling (1). | On vehicles with code (290) Windowbag and code (293) left and right sidebag in rear | |
14 | Unclip lugs (9) on C-pillar paneling (1) from clips (10) in rear area with mounting wedge. | | |
15.1 | Unclip clip (15) from C-pillar paneling (1) with mounting wedge. | On vehicles without code (290) Windowbag | |
| |||
16.1 | Remove C-pillar paneling (1) | On vehicles without code (810) Sound system Installation: Ensure that the C-pillar paneling (1) is seated correctly below the edge guard (11) in the rear door, the strip (13) (with code (290) Windowbag) is seated correctly in the windowbag retaining strip below the headliner (arrows B) and the lugs (9) are seated correctly in the clips (10). | |
16.2 | Remove C-pillar paneling (1) until electrical connector of left rear surround speaker (H4/54) or right rear surround speaker (H4/57) is accessible. | On vehicles with code (810) Sound system Installation: Ensure that the C-pillar paneling (1) is seated correctly below the edge guard (11) in the rear door, the strip (13) (with code (290) Windowbag) is seated correctly in the windowbag retaining strip below the headliner (arrows B) and the lugs (9) are seated correctly in the clips (10). | |
17.1 | Disconnect electrical connector from left rear surround speaker (H4/54) or right rear surround speaker (H4/57) | On vehicles with code (810) Sound system | |
18 | Guide seat belt (12) through opening in C-pillar paneling (1) and remove C-pillar paneling (1) | ||
19.1 | Remove left rear surround speaker (H4/54) or right rear surround speaker (H4/57) | When replacing C-pillar paneling (1) on vehicles with code (810) Sound system | |
20 | Install in the reverse order |
Seat belts/emergency tensioning retractors
Mounting wedge
110 589 03 59 00
Odkazované dokumenty
- ar8262p7855ak Demontáž, montáž reproduktoru v obložení C-sloupku
- ar9160p0694bk