Repair of mounting support under left B-pillar in panel van is shown |
1 | Mounting support at B-pillar |
D61.25-0006-06
| Remove | ||
Warning | Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units. | Store airbag units with deployment side facing up; do not expose to temperatures greater than 100 °C. When working on these units, disconnect the power supply. | |
Topical note | Notes on performing repair, body work and welding on vehicles with airbags and RTE units | ||
Topical note | General information on body repair | ||
1 | Remove seat base | The repair description must also be used accordingly for the right side of the vehicle | |
2 | Remove entrance box | ||
3 | Remove other detachable parts in the repair area | ||
4 | Cover all detachable body components that remain in the area to be repaired | ||
5 | Cut off mounting support at B-pillar (1) | ||
Bore spot welds. | |||
Spot weld milling cutter | |||
| Install | ||
6 | Prepare connecting points of mounting support at B-pillar (1) for installation | ||
7 | Align connecting plates, grind them off and coat them with zinc dust paint | Zinc dust paint suitable for spot welding | |
8 | Prepare mounting support at B-pillar (1) for installation | ||
Danger | The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system. | |
9 | Weld in mounting support at B-pillar (1) | ||
Topical note | Measures for preventing damage to vehicles or components when performing electric welding work | ||
General notes on welding | |||
10 | Grind off any residue welding material | ||
11 | Install entrance box | ||
12 | Vacuum out hollow cavities | | |
13 | Clean areas repaired and priming with MB primer filler | ||
14 | Supplement standard seals with MB body sealant | ||
White sealing compound, 310 ml, DBL 6069.20 | |||
15 | Supplement standard underfloor protection with MB permanent underbody sealant | ||
16 | Paint repair area adjacent surfaces | ||
17 | Add cavity preserving agent | ||
18 | Install seat base | ||
19 | Reinstall other removed detachable parts |
201 589 00 51 00
Spot weld milling cutter
Odkazované dokumenty
- ah0000n000501a Opatření k zamezení poškozením vozidel nebo součástí při elektrickém svařování
- ah6000n000101a Všeobecné pokyny k opravě karoserie
- ah6000n000501a Všeobecné pokyny ke svařování
- ah9100p000201m Upozornění k provedení opravárenských prací, prací na karoserii a svářečských prací u vozidel s jednotkou airbagu nebo jednotkou předpínače bezpečnostního pásu
- ar6110d5814a
- ar6110d5814a
- ar6125d000301a
- ar6125d000302a
- ar6125d000303a
- ar6125d000304a
- ar6420d0002a
- ar9710d4000a
- as0000z000701a Nebezpečí ohrožení života vysokým napětím při elektrickém svařování. Nebezpečí exploze při svařování v dosahu snadno vznětlivých látek. Nebezpečí poranění odstřikem a ultrafialovým zářením při svařování.
- as9100z000101d Nebezpečí poranění při kontrolních a opravných pracích na jednotkách airbagu nebo předpínače bezpečnostního pásu