W26.60-1350-09
1 | Cover | 5 | Grub screw | 10 | Retaining ring | ||
2 | Detent segment | 6 | Grub screw | 11 | Bolts | ||
3 | Shift housing | 8 | Shift shaft | S28 | Neutral position switch | ||
4 | Cap | 9 | Shift housing | Y36 | Splitter group solenoid valve |
Caution | Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil | Wear protective gloves, protective clothing and safety glasses. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Notes on compressed air connection systems | |||
| Remove | ||
1 | Remove lock rod for interlock. | ||
2 | Remove shift module. | ||
3 | Remove main shutoff valve. | ||
4 | Remove neutral position switch (S28). | ||
5 | Disconnect electrical connector from splitter group solenoid valve (Y36). | ||
6 | Remove cap (1) from shift housing (3). | ||
7 | Remove cap (4) from shift housing (3). | ||
8 | Heat up grub screw (5) using suitable means and unscrew from detent segment (2). | ||
9 | Heat up grub screw (6) using suitable means and unscrew from shift housing (3). | ||
10 | Pull detent segment (2) off gearshift shaft (8). | ||
11 | Remove retaining ring (10) from gearshift shaft (8). | ||
12 | Remove shift housings (3, 9). | ||
13 | Remove gearshift shaft (8). | To do so, push the gearshift shaft (8) toward the shift housing (9) using a suitable object, e.g. hammer handle. | |
| Clean | ||
14 | Clean sealing surfaces on shift housings (3, 9) and on cap (1). | Assembly cleaner | |
| Install | ||
15 | Install gearshift shaft (8). | ||
16 | Install shift housing (3) with new O-rings and new sealant. | Shift housing with bearing flange to transmission | |
Loctite 5203 sealant | |||
17 | Coat grub screw (6) with thread locking compound and screw into shift housing (3). | Thread locking adhesive, Loctite 241 | |
18 | Install shift housing (9) with new sealant. | Shift housing with bearing flange to transmission | |
Loctite 5203 sealant | |||
19 | Attach new retaining ring (10) to gearshift shaft (8). | ||
20 | Push detent segment (2) onto gearshift shaft (8). | The long, flat side of the detent segment (2) must point toward the shift housing (3). | |
21 | Coat grub screw (5) with thread locking compound and screw into detent segment (2). | Thread locking adhesive, Loctite 241 | |
22 | Coat new cap (4) with thread locking compound and install in shift housing (3). | Thread locking adhesive, Loctite 241 | |
23 | Attach cap (1) with new sealant to shift housing (3). | Cover to shift housing | |
Loctite 5203 sealant | |||
24 | Connect electrical connector to splitter group solenoid valve (Y36). | ||
25 | Install neutral position switch (S28). | ||
26 | Install main shutoff valve. | ||
27 | Install shift module. | ||
28 | Install lock rod for interlock. |
Odkazované dokumenty
- ah0018n000101a Pokyny k systémům konektorových spojů tlakového vzduchu
- ar2619g0003ae
- ar2660g0025ae
- ar2660g0030ae
- ar2660g0630ae
- as0000z000201a Nebezpečí poranění kůže nebo očí při zacházení s horkými nebo žhavými předměty
- as0040z000101a Nebezpečí poranění kůže a očí při manipulaci s převodovým olejem. Nebezpečí ohrožení zdraví při požití převodového oleje