Shown on model 437.465 |
1 | Engine cover |
2 | Sleeve |
3 | Coolant pipe (only for model 405.1/2, model 437.465) |
4 | Clip |
G01.10-3162-11
Shown on engine 904 |
1 | Engine cover |
5 | Spacer sleeve |
6 | Decoupling element |
7 | Washer |
8 | Screw |
9 | Electrical connection of vehicle wiring harness |
10 | Engine wiring harness electrical connector |
11 | Fill level sensor electrical line |
A6 | MR (PLD) control unit |
A | Pulling out (locking clamp) |
B | Swiveling (locking clamp) |
G07.15-3215-06
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Remove/install | ||
1 | Switch off ignition. | ||
2 | Drain coolant and capture in a clean container. | ||
| Only for engine 900.915/916 in model 405.05 | ||
3.1 | Tilt cab to repair position. | Model 405, model 437.42/43 | |
3.2 | Open hood. | Model 437.46 | |
See information from body manufacturer. | |||
4 | Fully remove air filter housing. | Only for engine 900.915/916 in model 405.05 | |
5 | Remove engine cover. |
| |
6 | Remove coolant pipe in front of the engine cover (1). | Only for engine 900.915/916 in model 405.05 | |
7 | Remove air intake pipe from air filter to the exhaust gas turbocharger. | Only for engine 900.915/916, 902.923/924/935, 904.927/928, 906.935/955 in model 405 | |
8 | Remove clamp (4) from the engine cover (1). | ||
9 | Remove coolant pipe (3) from the engine. | Only for model 405.1/2, 437.465 | |
There is a sleeve (2) between the engine and the bracket of the coolant pipe (3). | |||
10 | Remove engine cover (1). | ||
11 | Remove cable ties of the wiring of the engine wiring harness. | Only for engine 900, 904, 924 | |
Installation: Replace cable tie. | |||
12 | Remove vehicle wiring harness electrical connector (9) by pulling out (A) the securing bracket, releasing, and removing from the MR (PLN) control unit (A6). | ||
13 | Release engine wiring harness electrical connector (10) by swiveling (B) the securing bracket and removing from the MR (PLN) control unit (A6). | ||
14 | Remove fill level sensor electric line (11) from MR (PLN) control unit (A6). | ||
15 | Remove oil dipstick tube from crankcase. | If installed. | |
16 | Remove screws (8) and remove MR (PLN) control unit (A6). | Installation: Observe installation position of the decoupling elements (6), washers (7), and spacer sleeves (5). | |
Screw, MR/PLD control unit to crankcase | |||
17 | Install in the reverse order | ||
18 | Check, correct coolant level. | ||
| Only for engine 900.915/916 in model 405.05 | ||
19 | Teach in transponder key. | Only when installing new MR (PLN) control unit (A6). | |
Only for model 405.1/2 with code E08 (electronic immobilizer), model 405.05 | |||
20 | Connect diagnostic system and start XENTRY. | ||
21 | Perform quick test, print out, and file in a tamperproof manner. | There must be no fault codes in the control units being updated. | |
If fault codes are still present in control units being updated, | |||
| |||
then process the fault codes. | |||
After obtaining special order. | |||
22 | End XENTRY and remove the diagnostic system. |
Odkazované dokumenty
- ah5400p000101a Upozornění k zamezení poškozením elektronických součástí elektrostatickým výbojem
- ap2000g2010b Zkontrolovat, vyrovnat hladinu kapaliny chladicího systému motoru. Zkontrolovat,vyrovnat podíl ochrany proti korozi/mrazu
- ap2000g2080b Výměna chladicí kapaliny
- ar0110g2405e
- ar6080g0005b
- ar6080g0005b
- ar8057g0010b