Remove/install oil pan

AR01.45-B-7500TC

Remove/install oil pan

30.10.2019

Engine

904.9 in model 958

Engine

906.9 in model 958

Modification notes

20.09.2019

Oil pan from the engine to the block

Engine 904.9, 906.9

BA01.45-B-1001-01B

30.10.2019

Oil pan from the engine to the block

BA01.45-B-1001-01B

30.10.2019

Oil pan drain plug

BA01.45-B-1002-01B

1

Oil pan

2

Sealing gasket

3

Bolt

4

Oil filling piping

5

Seal ring

6

Oil outlet plug

7

Electric harness of the engine

B14

Oil level sensor

 

Remove/install

 Warning

Risk of injury caused by body parts being pinched or crushed as cab is tilted

Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut.

AS60.80-Z-0001-01A

1

Tilt the cabin

2

Drain and collect the motor oil

.

AR18.00-B-3035-02TA

 .Oil pan drain plug

*BA01.45-B-1002-01B

 .Engine oil

*BF18.00-B-1001-01B

3

Remove the oil filling pipe (4) from the oil sump (1)

4

Detach the engine wiring harness assembly (7) on the oil level sensor (B14) and release the electric line from the oil level sensor (B14).

5

Remove the drive oil lines from the brackets and attach them to the side

 Only for Code (N55), transmission oil cooling.
Do not detach the gearbox oil lines.

6

Remove the screws (3), then remove the oil sump (1)


Discard the screws (3) after disassembly.
Otherwise the chemical lock will no longer be efficient.

 Use the microencapsulated screws (3) for mounting M8x35 - N000000002815

 Installation: clean the sealing surfaces and apply the new seal (2)

 .Oil pan from the engine to the block

*BA01.45-B-1001-01B

7

Remove the oil level sensor (B14)

 Only when replacing the oil sump (1).

 .Oil level sensor in the oil pan

*BA18.40-B-1002-01A

8

Installation in reverse order

9

Check the engine oil level with the dipstick or on the display; fill up if necessary

 Note the required engine oil quality in the maintenance system, or the prescription of auxiliary supplies.

 Warning

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

10

Start the engine and, at idle, note the oil pressure indicator

 Actuate the starter for no more than 90 seconds.
Only repeat the starting procedure after a pause of at least 2 minutes elapses.

 Do not speed the engine while no oil pressure is indicated.
After approximately 10 sec., the manometer must indicate the oil pressure

.Engine oil pressure, minimum permissible

*BE18.00-B-1001-01A

11

Stop the engine and check for leaks

Oil pressure

Number

Designation

Engine 904.9, 906.9

BE18.00-B-1001-01A

Engine oil pressure, minimum permissible

idle rotation

bar

0,5

maximum rotation

bar

2,5

 Oil pan

Number

Designation

Engine 904.9, 906.9

BA01.45-B-1001-01B

Oil pan from the engine to the block

M8x40

Nm

25

M8x35

Nm

35

 Oil pan

Number

Designation

Engine 904.9, 906.9

BA01.45-B-1002-01B

Oil pan drain plug

M20x1.5

Nm

65

M22x1.5

Nm

-

M26x1.5

Nm

85

M261,5 with valve

Nm

-

 Oil level and pressure indicator

Number

Designation

Engine 904.9, 906.9

BA18.40-B-1002-01A

Oil level sensor in the oil pan

Nm

60

 Filling volume for engine lubrication

Number

Designation

Engine 904.9

Engine 906.9

BF18.00-B-1001-01B

Engine oil

Check the correct level

Oil pan

litros

15,0

28

Filter

litros

0,8

1,3

Maximum capacity after repair on the engine with drained oil channels

litros

-

-

Oil class

MB 228.3, 228.5

MB 228.3, 228.5