ar8370w5685d

Remove, install overheating sensor

Loại ar · chủ đề 83.70 · phiên bản 0102 · 2004-09-17

Áp dụng cho: MODEL 375.4 with BODY 375.840 with CODE (H60) Warm air heater "Eberspächer D1 LP" MODEL 944 with BODY 944.899 with CODE (H60) Warm air heater "Eberspächer D1 LP" MODEL 950, 952, 953, 954 with BODY 942.899 with CODE (H60) Warm air heater "Eberspächer D1 LP" MODEL 970, 972, 974, 975, 976 with BODY 972.899 with CODE (H60) Warm air auxiliary heater "Eberspächer" D1 LP MODEL 950, 952, 953, 954 with BODY 940.899 with CODE (H60) Warm air heater "Eberspächer D1 LP"'

Không có bằng “vi”; đang hiển thị bằng tiếng Anh.

Vị trí

Nhóm chức năng 3 Body › 83 Climate control › 83.70 Auxiliary/supplementary heater — Dòng 375 (mẫu 4**, 840) · Dòng 940 (mẫu 899) · Dòng 942 (mẫu 899) · Dòng 944 · Dòng 950 · Dòng 952 · Dòng 953 · Dòng 954 · Dòng 970 · Dòng 972 · Dòng 974 · Dòng 975 · Dòng 976

EinPAS 39 Heating/ventilation/cooling › 39.25 Stationary heater/auxiliary heater › 39.25.12 Sensor/switch/wiring harness — Dòng 375 (mẫu 4**, 840) · Dòng 940 (mẫu 899) · Dòng 942 (mẫu 899) · Dòng 944 · Dòng 950 · Dòng 952 · Dòng 953 · Dòng 954 · Dòng 970 · Dòng 972 · Dòng 974 · Dòng 975 · Dòng 976

AR83.70-W-5685D

Remove, install overheating sensor

22.5.97

MODEL 375.4 with BODY 375.840 with CODE (H60) Warm air heater "Eberspächer D1 LP"

MODEL 944 with BODY 944.899 with CODE (H60) Warm air heater "Eberspächer D1 LP"

MODEL 950, 952, 953, 954 with BODY 942.899 with CODE (H60) Warm air heater "Eberspächer D1 LP"

MODEL 970, 972, 974, 975, 976 with BODY 972.899 with CODE (H60) Warm air auxiliary heater "Eberspächer" D1 LP

MODEL 950, 952, 953, 954 with BODY 940.899 with CODE (H60) Warm air heater "Eberspächer D1 LP"

Remove, install overheating sensor

W83.70-0085-06

1 Upper housing shell

2 Body-bound rivet

3 Fuse

4 Overheating sensor

5 Retaining clamp

6 Outlet scoop

Removing, installing

1

Remove housing shells

AR83.70-W-5808B

2

Disconnect connector of overheating sensor (4)

Installation: When assembling, ensure correct cable routing.

3

Detach overheating sensor

Installation: Replace fuse (3).

4

Install in the reverse order

Danger!

Risk of explosion from fuel vapors, risk of poisoning from inhaling combustion gases and risk of injury from burns during and after operation of heater unit.

Do not operate stationary heater, auxiliary heater or engine with heater booster in closed areas or when refueling. Allow heater unit to cool down after operation and wear protective gloves.

AS83.70-Z-0002-01A

5

Check function of stationary heater

AR83.70-W-5302-02C

Tài liệu được tham chiếu