ar8370d5938b

Removing and installing printed circuit board

Loại ar · chủ đề 83.70 · phiên bản 0105 · 1998-07-31

Áp dụng cho: MODEL 901.06#, 902.06# /07#, 903.06# /07#, 904.06# ## up to 753730 up to 31.10.97 with CODE (H11) Hot air auxiliary heater Heater designation B3L-C MODEL 901.36# /37# /46#, 902.36# /37# /46# /47#, 903.36# /37# /46# /47#, 904.36# /46# ## up to 753730 up to 31.10.97 with CODE (H11) Hot air auxiliary heater Heater designation D3L-C

Không có bằng “vi”; đang hiển thị bằng tiếng Anh.

Vị trí

Nhóm chức năng 3 Body › 83 Climate control › 83.70 Auxiliary/supplementary heater — Dòng 901 (mẫu 06*, 36*, 37*, 46*) · Dòng 902 (mẫu 06*, 07*, 36*, 37*, 46*, 47*) · Dòng 903 (mẫu 06*, 07*, 36*, 37*, 46*, 47*) · Dòng 904 (mẫu 06*, 36*, 46*)

EinPAS 39 Heating/ventilation/cooling › 39.25 Stationary heater/auxiliary heater › 39.25.30 Heater — Dòng 901 (mẫu 06*, 36*, 37*, 46*) · Dòng 902 (mẫu 06*, 07*, 36*, 37*, 46*, 47*) · Dòng 903 (mẫu 06*, 07*, 36*, 37*, 46*, 47*) · Dòng 904 (mẫu 06*, 36*, 46*)

AR83.70-D-5938B

Removing and installing printed circuit board

4.11.96

MODEL 901.06#, 902.06# /07#, 903.06# /07#, 904.06# ## up to 753730 up to 31.10.97 with CODE (H11) Hot air auxiliary heater
Heater designation B3L-C

MODEL 901.36# /37# /46#, 902.36# /37# /46# /47#, 903.36# /37# /46# /47#, 904.36# /46# ## up to 753730 up to 31.10.97 with CODE (H11) Hot air auxiliary heater
Heater designation D3L-C

Removing and installing printed circuit board

D83.70-0032-06

1 Allen bolt
2 Cover
3 Gasket
4 Electrical connector for flame sensor
5 Electrical connector for overheat switch

6 Electrical connector for blower motor
7 Circuit board

Removal, installation

Danger!

Fuel vapors present an explosion hazard. Combustion gases are toxic when inhaled. Heater can cause severe burns during and after operation

Do not start up or operate stationary heaters or engines with heater boosters in closed rooms or in the vicinity of service stations. Allow heater to cool off after operation and wear protective gloves.

AS83.70-Z-0002-01A

Danger!

Fuel vapors present an explosion hazard. Fuel vapors are toxic when inhaled or absorbed. Contact with fuel can cause eye and skin injury.

Fire, open lights and smoking prohibited.
Fill and store fuel only in containers intended for this purpose and marked accordingly.

Wear protective clothing when handling fuel.

AS47.00-Z-0001-01A

1

Remove heater

Models 901.06, 902.06/07, 903.06/07, 904.06

AR83.70-D-5302B

Models 901.36/37/46, 902.36/37/46/47, 903.36/37/46/47, 904.36/46 left-hand steering

AR83.70-D-5302E

Models 901.36/37/46, 902.36/37/46/47, 903.36/37/46/47, 904.36/46 right-hand steering

AR83.70-D-5302D

2

Remove cover (2) together with gasket (3)

Installation: Check gasket for damage and replace, if necessary.

3

Unhook circuit board (7)

Press lug (arrow) down.

4

Pull circuit board (7) out until electrical connectors (4, 5, 6) are accessible

5

Disconnect electrical connectors (4, 5, 6)

6

Completely pull out circuit board (7)

Notes on handling circuit boards

AH00.00-N-0003-01A

7

Install in opposite order

Tài liệu được tham chiếu