ar2010i2455b

Test coolant thermostat

Tür ar · konu 20.10 · sürüm 0105 · 2007-08-07

Geçerli olduğu: ENGINE 904.925 in MODEL 8AB390.053 /054 ENGINE 904.941 in MODEL 684.482 ENGINE 904.965 in MODEL 8 AB390.053 /054

“tr” dilinde mevcut değil; İngilizce gösteriliyor.

Konumu

Fonksiyon grubu 1 Motor › 20 Motor soğutma › 20.10 Soğutma maddesi pompası, Soğutma maddesi termostatı — Seri 390 (modeller 053, 054) · Seri 684 (modeller 482) · Seri 904 (modeller 925, 941, 965)

EinPAS 15 Motor › 15.25 Motor soğutma sistemi › 15.25.30 Pompa/Termostat/Ön ısıtma cihazı — Seri 390 (modeller 053, 054) · Seri 684 (modeller 482) · Seri 904 (modeller 925, 941, 965)

^

AR20.10-I-2455B

Test coolant thermostat

23.7.07

ENGINE 904.925 in MODEL 8AB390.053 /054

ENGINE 904.941 in MODEL 684.482

ENGINE 904.965 in MODEL 8 AB390.053 /054

Test coolant thermostat

W20.10-0005-04

1 Coolant thermostat

1/1 Main valve

1/2 Bypass valve

Test coolant thermostat

T20.10-0002-01

Checking

Danger!

Risk of injury to skin and eyes caused by handling hot or glowing objects.

Wear safety gloves, protective clothing and safety glasses, if necessary.

AS00.00-Z-0002-01A

1

Remove coolant thermostat (1)

Engine 904.925/965

AR20.10-A-2460LA

Engine 904.941:

* only for Indonesia

AR20.10-I-2460B

2

Attach coolant thermostat (1) to a wire and hang in a vessel filled with water

3

Warm up water until bypass valve (1/2) is closed while stirring the water and permanently measure the water temperature

The heating-up rate should be not more than 1°C to 2°C/minute from about
8 °C below the opening temperature of the coolant thermostat (1).

*BE20.10-N-1001-02A

*BE20.10-N-1003-02A

If specified values are not achieved:

Replace coolant thermostat (1).

4

Continue to warm up water until the main valve (1/1) is fully opened

The main valve (1/1) must be fully opened after 6 to 8 minutes. Check the water temperature for a fully opened main valve (1/1). If the specified value is not reached:

*BE20.10-N-1002-02A

Replace coolant thermostat (1).

5

Remove coolant thermostat (1) from vessel and measure distance between collar on coolant thermostat (1) and main valve (1/1) plate

Measurement should take place immediately after removing the coolant thermostat (1) from the vessel.

Note the measured value.

6

Allow coolant thermostat (1) to cool off until main valve (1/1) is closed

7

Measure distance between collar on coolant thermostat (1) and main valve (1/1) plate

Note the measured value.

8

Check stroke of the main valve (1/1)

Calculate stroke on the basis of the previously noted measurements. If the specified value is not reached:

*BE20.10-N-1002-02A

Replace coolant thermostat (1).

9

Install coolant thermostat (1)

Engine 904.925/965

AR20.10-A-2460LA

Engine 904.941:

* only for Indonesia

AR20.10-I-2460B

Check values for coolant thermostat

Number

Designation

Engine
900.9, 902.9, 904.9, 906.9

BE20.10-N-1001-02A

Coolant thermostat - start of opening

°C

83 (2)

BE20.10-N-1002-02A

Coolant thermostat - main valve

Full opening

°C

95

Stroke

mm

8

BE20.10-N-1003-02A

Coolant thermostat - bypass valve closed at

°C

92

Atıfta bulunulan belgeler