Function requirements for disk changer in general
Circuit 30g ON
Transport mode not active
Disk changer, general
The CD/DVD changer is integrated in the audio equipment and contains a magazine for up to six CDs or DVDs.
The CD/DVD changer enables the following function sequences to be performed:
Load CD or DVD function sequence
Eject CD or DVD function sequence
Shown on audio equipment with CODE 510 (Audio 20 CD with CD changer, 6-disk) |
2 | Keyboard (operating panel on right) |
4 | Load button (CD/DVD eject button) |
9 | Drive slot (CD/DVD drive) |
P82.60-8375-04
Load CD or DVD function sequence
When the Load button is pressed on the audio equipment, the "Cartridge menu" appears on the Audio/COMAND display (A40/8), including details on the last selected CD/DVD slot in the CD/DVD changer. The required CD/DVD slot can be selected by turning or pressing on the Audio/COMAND control panel (A40/9) to the left or right. Selection is confirmed by pressing vertically onto the Audio/COMAND control panel.
The desired CD/DVD slot can also be selected using the keypad (buttons 1 to 6) on the audio equipment .
A CD or DVD must not be inserted until the corresponding request to do so appears on the Audio/COMAND display, e.g. "Please insert Disc 2". After inserting the CD or DVD into the CD/DVD drive the Audio/COMAND display shows a message, e.g. "Disc 2 loading...".
The duration of the loading process can vary depending on the type of data storage device involved.
Once the CD or DVD is loaded, the display changes back to the "Cartridge menu". If no CD or DVD is inserted, the display also changes after t = 20 s back to "Cartridge menu". A loaded CD or DVD is shown in the "Cartridge menu".
The "Fill up empty spaces" menu enables several CDs or DVDs to be loaded one after the other. A CD or DVD may not be inserted until the corresponding request to do so appears on the Audio/COMAND display, e.g. "Please insert Disc 3". The "audio equipment" now presents the empty CD/DVD compartments for loading.
The signals from the Audio/COMAND control panel are forwarded over the telematics CAN (CAN A) to the audio equipment, on vehicles with CODE B56 (Drive Kit Plus for iPhone® 4/4S) or CODE B62 (Drive Kit Plus for iPhone® 5s/5c/5 via the follwing route):
Telematics CAN
Control unit for Drive Kit for iPhone® (N123/7)
Telematics CAN
The audio equipment transmits control signals via the telematics CAN to the Audio/COMAND display. The video signals are transmitted from the audio equipment over a low voltage differential signal (LVDS) line to the Audio/COMAND display, on vehicles with CODE B56 (Drive Kit Plus for iPhone® 4/4S) or CODE B62 (Drive Kit Plus for iPhone® 5s/5c/5) through the control unit for the Drive Kit for the iPhone®.
Eject CD or DVD function sequence
After pressing the Load button on the audio equipment , the Audio/COMAND display shows the "Cartridge menu" including details on the last selected CD/DVD slot in the CD/DVD changer. The desired CD/DVD slot can be selected by turning or pressing the controls on the Audio/COMAND control panel to the left or right. Selection is confirmed by pressing vertically onto the Audio/COMAND control panel.
The desired CD/DVD slot can also be selected using the keypad (buttons 1 to 6) on the audio equipment.
While the CD or DVD is ejected, a message appears in the Audio/COMAND display (e.g. "Disk 2 being ejected ..."). As soon as the CD or DVD appears in the CD/DVD drive slot, a corresponding message is shown (e.g. "Please remove disc 2"). Once the CD or DVD is removed, the display changes back to the "Cartridge menu".
If the CD or DVD is not removed, the CD or DVD is loaded again.
The "Eject all" menu enables all the loaded CDs or DVDs to be removed one after the other. As soon as the CD or DVD appears in the CD/DVD drive slot, a corresponding message appears (e.g. "Please remove disc 3"). Once the CD or DVD is removed from the CD/DVD drive slot, the next CD or DVD is ejected until the entire CD/DVD cartridge is empty.
An ejected CD or DVD is shown in the "Cartridge menu" as an empty CD/DVD slot.
The eject procedure can be stopped at any time by pressing the load button on the audio equipment or the "Back" button (A40/9s2) of the Audio/COMAND control panel.