AR91.40-D-1010A | Remove/install seat belt (front seat) | 23.4.96 |
MODELS 901, 902, 903, 904, 905 except CODE (SA5) Driver airbag
MODELS 901, 902, 903, 904, 905 except CODE (SA6) front passenger airbag
MODELS WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4, YD5, YD6, YD7 except CODE (SA5) Driver airbag
MODELS WD1, WD2, WD3, WD6, WD7, XD1, XD2, XD3, XD4, XD5, XD6, XD7, YD1, YD2, YD3, YD4, YD5, YD6, YD7 except CODE (SA6) front passenger airbag
MODELS 690.6
D91.40-0001-06
1 Bolt
2 Door seal
3 Door seal (on cargo space sliding door)
4 Panel
5 Seat belt height adjustment paneling
6 Bolt
7 Reel
8 Guide
9 Seat belt height adjustment driver
10 Lug
11 Seat belt height adjustment mechanism
D91.40-1105-01
13 Top bolt for seat belt height adjustment
14 Bottom bolt for seat belt height adjustment
| Remove | ||
1 | Unscrew bolt (1) from seat belt on seat frame. | ||
2.1 | Remove door seal (2) from stay of door cutout on B-pillar | ||
2.2 | Remove door seal (3) from door cutout stay on B-pillar | With load compartment sliding door | |
3 | Lever paneling (4) off B-pillar (clipped on) and lift off | ||
4 | Pull seat belt out of lining | ||
5 | Unscrew bolt (6) from upper guide point | ||
6 | Unscrew reel (7) and remove out of guide (8) on B-pillar | ||
7 | Check that skid for belt height adjuster functions correctly, replace if necessary. | ||
| Install | ||
8 | Tighten bolts for belt height adjuster (13, 14) on B-pillar | Only when replacing | |
| |||
| |||
9 | Remove retaining clips (7) from B-pillar and insert into paneling. | ||
10 | Insert reel (7) into guide (8) on B-pillar and tighten. | | |
11 | Tighten seat belt on upper guide point. | | |
12 | Move seat belt through paneling | ||
13 | Position seat belt height adjustment driver (9) with paneling on lug (10) of seat belt height adjustment mechanism (11). | ||
14 | Clip paneling onto B-pillar | ||
15 | Press door seals (2) onto stay of door cutout on B-pillar | Paneling edge should be placed under floor covering | |
16.1 | Press door seal (3) of door cutout stay on B-pillar | With load compartment sliding door | |
Paneling should be placed below floor paneling | |||
17 | Secure seat belt to seat frame with bolt (1) | | |
| Inspect | ||
18 | Check that seat belt and height adjustment mechanism function correctly |
Seat belts/emergency tensioning retractors
Number | Designation | Models 690.6, 901, | Models 903.612/613 | Models | |
BA91.40-N-1001-01B | Bolt, seat belt to seat case | Nm | 35 | - | 35 |
BA91.40-N-1002-01B | Bolt to upper guide point | Nm | 35 | 35 | 35 |
BA91.40-N-1003-01B | Inertia reel to B-pillar | Nm | 35 | 35 | 35 |
BA91.40-N-1004-01B | Upper bolt, seat belt height adjuster to | Nm | 35 | 35 | 35 |
BA91.40-N-1005-01B | Lower bolt, seat belt height adjuster to | Nm | 23 | 23 | 23 |