P83.30-4892-09
Shown on model 222 with code P20 (Driving Assistance Package Plus) |
1 | Reinforcement | 5 | Retaining clips | |
2 | Sealing | 6 | Bolts | |
3 | Engine air intake ducts | 7 | Electrical connector | |
4 | Hood release cable | B29 | Front long-range radar sensor |
P83.30-4968-09
Shown on model 217 with code 610 (Night View Assist) and code P20 (Driving Assistance Plus Package) |
1 | Reinforcement | 17 | Radiator guides | |
6 | Bolts | 18 | Spray nozzle | |
7 | Electrical connector | B29 | Front long-range radar sensor | |
7.1 | Electrical connector | B84/11 | Night View Assist infrared camera 2 |
Shown on model 222 |
8 | Drier cap |
9 | Retaining ring |
10 | Pin |
11 | Drier head |
12 | Drier module riser line |
13 | Desiccant bag |
16 | Drier module bracket |
P83.30-4893-06
Danger | Risk of fire due to ignition of R1234yf refrigerant on hot components. Risk of poisoning caused by inhaling overheated refrigerant vapors. Risk of injury to skin and eyes caused by contact with escaped R1234yf refrigerant and when working on pressurized parts. Risk of explosion due to formation of ignitable refrigerant/air mixtures | Never perform welding work on or near a closed air conditioning system. No smoking or open flames. Wear safety glasses and protective gloves. Work only in well ventilated rooms. Carry out repair work on the air conditioning system circuit only after the system has been evacuated.Model 217, 222 | |
Warning | Risk of poisoning caused by inhaling overheated refrigerant vapors from an air conditioning system containing R134a. Risk of injury to skin and eyes caused by contact with liquid R134a refrigerant and when working on pressurized parts | Never perform welding work on or near a closed air conditioning system. No smoking or open flames. Wear safety glasses and protective gloves. Work only in well ventilated rooms. Carry out repair work on the air conditioning system circuit only after the system has been evacuated.Model 217, 222 | |
Topical note | Protect air conditioning circuit and components from moisture when carrying out repair work | ||
Notes on handling refrigerant R1234yf | Model 217, 222 | ||
Notes on handling refrigerant R134a | Model 217, 222 | ||
| Remove | ||
1 | Drain air conditioning system | ||
2 | Detach sealing (2) in area of front module | ||
3 | Remove engine intake air ducts (3) | Depending on the engine involved, only one engine air intake duct (3) is installed. | |
4.1 | Remove front bumper | Model 217 | |
4.2 | Remove radiator grille | Model 222 | |
5 | Open retaining clips (5) and unhook hood release cable (4) | ||
6 | Release and disconnect electrical connector (7) from front long range radar sensor (B29) | Model 217, 222 | |
7 | Release and disconnect electrical connector (7.1) from infrared camera for 2 Night View Assist (B84/11) | Model 217, 222 | |
8 | Unclip spray nozzle (18) from infrared camera for 2 Night View Assist (B84/11) | Model 217, 222 | |
9 | Remove bolts (6) from reinforcement (1) | ||
10 | Remove reinforcement (1) with upper radiator guides (17) | ||
11 | Unscrew drier cap (8) | ||
12 | Remove circlip (9) | ||
13 | Screw bolt M12 into drier head (11) and pull out drier head (11) | ||
14 | Use pliers to pull out drier module bracket (16) at pin (10) | ||
| Install | ||
15 | Apply new desiccant bag (13) on drier module riser line (12) | If the packaging of the new desiccant bag (13) is damaged, do not install it. | |
16 | Install drier module bracket (16) with new desiccant bag (13) | ||
17 | Remove bolt M12 from drier head (11) | ||
18 | Install retaining ring (9) | ||
19 | Screw in drier cap (8) | ||
20 | Install reinforcement (1) with upper radiator guides (17) | ||
21 | Tighten bolts (6) on reinforcement (1) | ||
22 | Clip in spray nozzle (18) for infrared camera for 2 Night View Assist (B84/11) | Model 217, 222 | |
23 | Plug electrical connector (7.1) onto infrared camera for 2 Night View Assist (B84/11) until it locks in to place | Model 217, 222 | |
24 | Plug electrical connector (7) onto front long range radar sensor (B29) until it locks into place | Model 217, 222 | |
25 | Clip hood release cable (4) into retaining clips (5) and close retaining clips (5) | ||
26.1 | Install radiator trim | Model 222 | |
26.2 | Install front bumper | Model 217 | |
27 | Install engine air intake ducts (3) | Depending on the engine involved, only one engine air intake duct (3) is installed. | |
28 | Install sealing (2) | ||
29 | Fill air conditioning system | ||
30 | Perform initialization of front long range radar sensor (B29) using a diagnostic system | Model 217, 222 | |
| |||
31 | Check air conditioning for proper operation |