Shown on model 213 |
1 | Rear muffler |
2 | Rear muffler |
3 | Elastomer bearing |
5 | Valve |
6 | Electrical connection |
P49.10-3196-06
Shown on model 238 |
22 | Clamp |
P49.10-3190-05
Danger ! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Danger ! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Danger ! | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
| Notes on self-locking nuts and bolts | ||
| Notes on avoiding damage through contamination and foreign objects | ||
| Remove | ||
1 | Release and disconnect electrical connection (6) at valve (5) | Engine 276.853 in model 213 | |
2 | Support rear muffler (1) | ||
| 000 588 11 62 00 Major assembly mount | ||
| 000 588 10 62 00 Support plate | ||
3 | Disconnect rear muffler (1) at connecting points (t) | If no clamps are installed. | |
4 | Detach rear muffler (1) at clamp from rear muffler (2) | If there is a clamp installed. | |
5 | Detach rear muffler (1) at clamp (22) from center exhaust system | Engine 276.8 in model 238 | |
6 | Remove rear muffler (1) from elastomer bearing (3) | ||
7 | Drain off and remove rear muffler (1) | ||
| 000 588 11 62 00 Major assembly mount | ||
| 000 588 10 62 00 Support plate | ||
8 | Remove combustion and corrosion residue at separating points | ||
9 | Deburr cutting edges on the connecting points and clean | If there was no clamp present. | |
10 | Check elastomer bearings (3) for damage | If the elastomer bearing (3) is damaged | |
| |||
Replace elastomer bearing (3). | |||
11 | Check the holder of the rear muffler (1) for damage | In case of damage to the holder | |
| |||
Replace holder. | |||
12 | Replace sealing ring of connecting point | Engine 276.8 in model 238 | |
| Install | ||
13 | Position clamp on center exhaust systems | If there was no clamp installed. | |
14 | Position rear muffler (1) and support | ||
| 000 588 11 62 00 Major assembly mount | ||
| 000 588 10 62 00 Support plate | ||
15 | Detach elastomer bearing (3) on rear muffler (1) | ||
16 | Fasten rear muffler (1) at center exhaust system with new clamp (22) | Engine 276.8 in model 238 | |
Clamp, front exhaust system to rear muffler | |||
17 | Fasten rear muffler (1) at center exhaust system with new clamp | Engine 276.8 in model 213 | |
Clamp, front exhaust system to rear muffler | |||
18 | Mount rear muffler (1) with new clamp on rear muffler (2) | Engine 276.8 in model 213Clamp between rear muffler | |
Engine 276 in model 238Clamp between rear muffler | |||
19 | Release and disconnect electrical connection (6) on valve (5) | Engine 276.853 in model 213 | |
Danger ! | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
20 | Perform an engine test run and check exhaust system for leaktightness |