ar4310p0355ew
Remove/install brake booster vacuum line
ประเภท ar · หัวข้อ 43.10 · เวอร์ชัน 0303 · 2012-10-12
ใช้กับ: MODEL 212 (except 212.095/098/195/298), 218
ไม่มีใน “th” แสดงเป็น อังกฤษ
ตำแหน่ง
กลุ่มฟังก์ชัน 2 Chassis › 43 Brakes - pneumatic system and auxiliary brakes › 43.10 Pneumatic brake unit — ซีรีส์ 212 (รุ่น 001, 002, 003, 004, 005, 006, 011, 020, 021, 023, 024, 025, 026, 027, 034, 035, 036, 040, 041, 047, 048, 052, 053, 054, 055, 056, 057, 059, 061, 065, 067, 072, 073, 074, 075, 076, 077, 080, 082, 087, 088, 089, 090, 091, 092, 093, 094, 097, 099, 133, 134, 136, 147, 148, 154, 162, 165, 167, 168, 201, 202, 203, 204, 205, 206, 211, 220, 221, 223, 224, 225, 226, 227, 234, 236, 247, 248, 254, 255, 256, 257, 259, 261, 265, 267, 272, 273, 274, 275, 276, 277, 280, 282, 287, 288, 289, 291, 292, 293, 294, 297, 299) · ซีรีส์ 218
EinPAS 21 Brakes/vacuum system/compressed-air system › 21.15 Service brake/vacuum system › 21.15.13 Line/hose/valve — ซีรีส์ 212 (รุ่น 001, 002, 003, 004, 005, 006, 011, 020, 021, 023, 024, 025, 026, 027, 034, 035, 036, 040, 041, 047, 048, 052, 053, 054, 055, 056, 057, 059, 061, 065, 067, 072, 073, 074, 075, 076, 077, 080, 082, 087, 088, 089, 090, 091, 092, 093, 094, 097, 099, 133, 134, 136, 147, 148, 154, 162, 165, 167, 168, 201, 202, 203, 204, 205, 206, 211, 220, 221, 223, 224, 225, 226, 227, 234, 236, 247, 248, 254, 255, 256, 257, 259, 261, 265, 267, 272, 273, 274, 275, 276, 277, 280, 282, 287, 288, 289, 291, 292, 293, 294, 297, 299) · ซีรีส์ 218
AR43.10-P-0355EW
| Remove/install brake booster vacuum line
| 30.7.12
|
MODEL
| 212 (except 212.095/098/195/298), 218
|
1
| Check valve
|
| 6
| Cover
|
| 10
| Screw/bolt
|
2
| Vacuum line
|
| 7
| Screws/bolts
|
| 11
| Wiring harness
|
4
| Rubber piping
|
| 8
| Nut
|
| 12
| Clips
|
5
| Release lug
|
| 9
| Separation point
|
| A7/7
| BAS brake booster
|
| Remove/install
|
|
|
1
| Operate the brake pedal several times when the engine is switched off
| In order to reduce the vacuum in the BAS brake booster (A7/7).
|
|
2
| Open engine hood and raise to vertical position
| MODEL 212, 218
|
|
|
|
| MODEL 212
| AR88.40-P-1000EW
|
3
| Remove air filter housing
| ENGINE 156, 272, 273
|
|
|
|
| ENGINE 156 in MODEL 212
| AR09.10-P-1150CMG
|
|
|
| ENGINE 272, 273 in MODEL 212
| AR09.10-P-1150EWS
|
4
| Remove engine cover
| ENGINE 642, 651
|
|
|
|
| Installation:
Engine 642:Ignition switched off.
|
|
5
| Unscrew nut (8)
| Nut, strut to suspension strut tower
| *BA62.30-P-1006-02G
|
6
| Remove clips (12) and take off strut
|
|
|
7
| Detach rubber edge strip (4)
|
|
|
8
| Unclip release lugs (5) and remove cover (6) with vacuum line (2) upwards
| If necessary the vacuum line (2) can be separated at the separation point (9). Both sections of the vacuum line (2) can be removed separately.
|
|
9
| Lift cover with wiring harness (11) off partition wall
|
|
|
10
| Remove screws/bolts (10)
|
|
|
11
| Unscrew screws/bolts (7) and remove bracket
|
|
|
12
| Pull vacuum line (2) with check valve (1) out of rubber seal of BAS brake booster (A7/7)
| Installation: Replace rubber seal.
|
|
13
| Detach vacuum line (2) from engine
|
|
|
14
| Remove vacuum line (2) upwards
| Pull the partition wall forward between wheel well.
|
|
15
| Install in the reverse order
|
|
|
16
| Carry out brake test on the test stand
|
|
|
|
|
| AP42.00-P-4290BA
|
Front end with front reinforcement
|
Number
| Designation
|
| MODEL 212
| MODEL 218
|
BA62.30-P-1006-02G
| Nut, strut to suspension strut tower
| Nm
| 30
| 30
|
เอกสารที่อ้างถึง
