Shown on model 171.442 |
1a | Pendulum support |
1b | Expansion reservoir |
3 | Wiper arms |
4 | Refrigerant pipe |
5 | Water collector |
28 | Retaining clamp |
29 | Retaining clamp |
F1 | Fuse and relay box |
P43.10-2035-06
1 | Tandem brake master cylinder |
8 | Vacuum line |
9 | Boot |
18 | Sealing ring |
20 | Connector |
21 | Seal |
23 | Nuts |
A7/7 | BAS brake booster |
A7/7b1 | BAS diaphragm travel sensor |
A7/7s1 | BAS release switch |
A7/7x1 | Diaphragm travel sensor connector |
A7/7x2 | Release switch and solenoid valve connector |
B34/1 | ESP brake pressure sensor 1 |
P42.10-2300-06
Shown on model 171.456 |
6a | Nuts |
9 | Boot |
23 | Nuts |
25 | Safety clip |
26 | Pin |
F1 | Fuse and relay box |
P43.10-2038-11
| Remove/install | ||
Caution | Risk of poisoning from swallowing brake fluid. Risk of injury from skin and eye contact with brake fluid | Only pour brake fluid into suitable and appropriately marked containers. Wear protective clothing and eye protection when handling brake fluid. | |
Topical note | Notes on externally invisible brake fluid loss | ||
Topical note | Brake fluid notes | ||
Topical note | Notes on repairs to brake system | ||
Topical note | Notes on self-locking nuts and bolts | ||
1 | Move wiper arms (3) into end position | ||
2 | Remove key from EIS electronic ignition lock control unit | ||
3 | Eliminate vacuum in BAS brake booster (A7/7) | Operate brake pedal several times until vacuum in BAS brake booster (A7/7) is reduced. | |
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
4 | Open hood | ||
Warning | Injury hazard from pinching and crushing, in extreme cases extremities can even be cut off when caught in windshield wiper mechanism. | When working on the windshield wiper mechanism, always switch off the ignition and store transmitter key outside of transmission range (at least 2 m). | |
5 | Remove wiper arms (3) | Remove and install wiper arm | |
Nut on wiper arm | |||
Puller | |||
6 | Remove air/water duct (5) | ||
7 | Remove torsion bar linkage (1a) from tandem master brake cylinder (1) | ||
8 | Remove tandem master brake cylinder (1) | ||
Do not detach expansion reservoir (1b) for brake fluid from tandem master brake cylinder (1). | |||
Installation: Check tandem master brake cylinder (1) on primary piston for leak tightness. | |||
Installation: Replace sealing ring (18). | |||
9 | Release and disconnect diaphragm travel sensor connector coupling (A7/7x1) from BAS diaphragm travel sensor (A7/7b1) | ||
10 | Release and disconnect indicator switch and solenoid valve connector coupling (A7/7x2) from BAS indicator switch (A7/7s1) | ||
11 | Release and disconnect connector coupling (20) from ESP pressure sensor 1 (B34/1) | ||
12 | Remove vacuum line (8) from BAS brake booster (A7/7) |
| |
Model 171.454/456/458/473 | |||
13 | Unclip refrigerant line (4) from retaining clamps (28, 29) and place to one side | Model 171.442/445 | |
14 | Remove left cover below instrument panel | ||
15 | Remove front cover of pedal assembly | ||
16 | Unscrew nuts (6a) from fuse and relay box (F1) in driver footwell | ||
Nut, fuse and relay module to body | |||
Bolt of clamping bracket for fuse and relay module to suspension strut tower | |||
17 | Remove safety clip (25); to do so, remove bolt (26) | ||
18 | Unscrew nuts (23) from BAS brake booster (A7/7) | Nut, brake booster carrier to front end | |
19 | Release fuse and relay box (F1) in engine compartment | ||
Pull fuse and relay box (F1) out of bulkhead. | |||
Nut, fuse and relay module to body | |||
Bolt of clamping bracket for fuse and relay module to suspension strut tower | |||
20 | Take out BAS brake booster (A7/7) | Installation: | |
Remove BAS brake booster (A7/7) from bulkhead and rotate by 45° counterclockwise. | |||
Pull fuse and relay box (F1) toward left when removing from BAS brake booster (A7/7). | |||
Installation: Install new seal (21). | |||
21 | Install in the reverse order | ||
22 | Bleed brake system | ||
23 | Connect STAR DIAGNOSIS, read out fault memory and erase if necessary | ||
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
24 | Check brake system for leaks | ||
Danger | Risk of death caused by limbs being caught or crushed by rotating parts when performing tests on the brake test stand | Never leave the vehicle unattended on the rollers except in an emergency. Ensure that no one is under the vehicle or near rotating parts during testing. In case of emergency, use the EMERGENCY OFF switch to shut down test stand. | |
25 | Carry out brake test on the test stand | ||
|
001 589 38 33 00
Puller
เอกสารที่อ้างถึง
- ah0000n000101a
- ah4200p000301a
- ah4210p940602a
- ah4250p000101a
- ap4200p4290ba
- ar2910p0320v
- ar4210p0010v
- ar4210p010001v
- ar4210p030002v
- ar4210p0310v
- ar4310p0355v
- ar4310p0355va
- ar5415p125601va
- ar6810p1500v
- ar8230p6100v
- ar8325p1402v
- ar8840p1000v
- as0000z000501a
- as0000z001101a
- as4200z000101a
- as4250z000101a
- as8230z000101a