ar4110p008503msa

Measure absolute angle at rear axle housing

ประเภท ar · หัวข้อ 41.10 · เวอร์ชัน 0101 · 2018-11-21

ใช้กับ: Model 257 Model 290 with engine 256.9

ไม่มีใน “th” แสดงเป็น อังกฤษ

ตำแหน่ง

กลุ่มฟังก์ชัน 2 Chassis › 41 Propeller shaft › 41.10 Propeller shaft — ซีรีส์ 257 · ซีรีส์ 290

EinPAS 17 Drivetrain/axle › 17.40 Propeller shaft › 17.40.30 Drive/all-wheel drive propeller shaft — ซีรีส์ 257 · ซีรีส์ 290

ใช้กับเครื่องยนต์/เกียร์ด้วย: 256 9**

AR41.10-P-0085-03MSA

Measure absolute angle at rear axle housing

Notes on measuring the drive shaft articulation angle

AH41.10-P-0002-01LF

000 588 04 19 00 Articulation angle inclinometer

WS26.00-P-0140B

Model

257

Model

290 with engine 256.9

Measure absolute angle at rear axle housing

Measurement of angle 4 at rear axle differential
An angle that has already been measured can be measured a second time if required. Here, with the Measurement menu displayed, press the STEP button repeatedly until the display shows it is ready to measure the relevant angle.

1.1

On rear axle differentials (3) with contact surfaces (4).
Clean dirt as well as paint and sealant residue from contact surfaces (4) on housing of rear axle differential (3).


Remove any unevenness on surface of material using a suitable tool.



1.2

On rear axle differentials (3) without contact surfaces (4).
Clean surfaces to the left and right of housing end cover of rear axle differential (3) free of contamination and paint and sealant residues.


P41.10-2392-01

Measure absolute angle at rear axle housing

2.1

On rear axle differentials (3) with contact surfaces (4).
Position sensor (020a) on contact surfaces (4) of housing of rear axle differential (3).


When each measurement is taken, the side of the sensor (020a) at which the spiral cable (020b) is connected must point in the direction of travel.
False measurements can occur otherwise.



2.2

On rear axle differentials (3) without contact surfaces (4).
Position adapter for universal rear axle differential (3) on suitable area and mount sensor (020a) on adapter for universal rear axle differential (3).


When each measurement is taken, the side of the sensor (020a) at which the spiral cable (020b) is connected must point in the direction of travel.
False measurements can occur otherwise.


P41.10-2393-01

Measure absolute angle at rear axle housing

The meter is ready to take a measurement. The display shows the measured values.

3

Press SAVE button.


The device saves the values.


Measurement value display message angle piece 4: Display, e.g. 2.68°

P41.10-2082-01

Measure absolute angle at rear axle housing

A confirmation message appears briefly, followed by Ready for next measurement (angle 5). The measurement is completed and stored in memory.

Display message confirmation

P41.10-2076-01

Measure absolute angle at rear axle housing

4.1

On rear axle differential (3) with contact surfaces (4).
Remove sensor (020a) from contact surfaces (4) of housing of rear axle differential (3).



4.2

On rear axle differentials (3) without contact surfaces (4).
Remove sensor (020a) and adapter for universal rear axle differential (3) from rear axle differential (3).


P41.10-2393-01

Measure absolute angle at rear axle housing

5.1

On rear axle differentials (3) with contact surfaces (4).
Protect contact surfaces (4) of housing of rear axle differential (3) from corrosion.



5.2

On rear axle differentials (3) without contact surfaces (4).
Protect surfaces to left and right of housing end cover of rear axle differential (3) from corrosion.


P41.10-2392-01

เอกสารที่อ้างถึง