B32.35-0029-09
B32.35-0030-09
1 | Front axle | 11 | Bearing bushing | |
2 | Front anti-roll bar | 12 | Tapered housing of the side arm terminal on the bar | |
3 | Lateral arm of the anti-roll bar | 13 | Ball-and-socket joint | |
4 | Self-locking nut | 14 | Tapered clamping shank | |
5 | Mounting bracket | 15 | Protection hood | |
6 | Flanged screw and nut | 16 | Elastic ring | |
7 | Bearing support | 17 | Metal ring | |
8 | Self-locking screw and nut | A | Lubricating grease | |
9 | Bearing cap | X | Maximum clearance allowed | |
10 | Bearing screw | Seta | Indicates the correct mounting position of the split pads |
| Remove | ||
1 | Disconnect the negative battery cable or turn off the main switch | For vehicles equipped with electronic engines, always observe the recommendations regarding the care with the vehicle electronics. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
2 | Lift the vehicle | When lifting the vehicle by the stringers of the frame and the axle hanging, with the bellows depressurized and without support, the excessive stroke of the dampers may damage them | |
3 | Remove and install the wheels, if necessary | ||
If using the appropriate lift, removing the wheels is not necessary. However, for certain jobs, it makes access easier. | |||
4 | Remove the self-locking nuts (4) for upper and lower fastening of the spherical terminals of the side arms (2), on both sides | ||
5 | Remove the terminals and remove the side arms (3) | To prevent damage to the threads, use a copper or brass hammer | |
6 | Remove the screws (10) and bearing caps (9), remove the front anti-roll bar (2) with the split pads (11) | ||
7 | Remove the flanged screws and nuts (6) and remove the brackets | If necessary, replace the brackets (5) from the side arms on the stringers. | |
8 | Remove the flanged bolts and nuts (8) and remove the brackets | If necessary, replace the brackets from the bearings (7). | |
| Check | ||
9 | Examine the side arms (3) with spherical terminals | .Play X maximum permissible at the terminal ball joints of the stabilizer side arms | |
In case of poor condition, excessive wear or deformation on the bar | |||
| |||
Replace. | |||
10 | Examine the anti-roll bar (2). | If deformed | |
| |||
Replace. | |||
11 | Examine the bearing supports (7) attached to the front axle | If necessary | |
| |||
Replace. | |||
12 | Examine the brackets (5) of the side arms on the stringers | If necessary | |
| |||
Replace, applying the background painting before mounting. | |||
| Install | ||
13 | If these have been removed, install the bearing brackets (7), secure them to the front axle (1) and use new flanged nuts (8) on the screws | .Supports (of stabilizer bearings) on the front axle | |
14 | Install the anti-roll bar (2) with new bipartite cushions (11) on the bearings and evenly tighten the bolts (10) to the specified torque | Lubricate lightly with petroleum jelly the contact part of the bar with the cushions. | |
Note the correct position of the split pads, whose splices should be at the position indicated by the arrows. | |||
.Stabilizer bearings caps | |||
15 | Install the brackets (5) on the stringers and secure them with flanged bolts and nuts (6) | Use new flanged nuts. | |
.Supports of rear and front arms of the stabilizer on the stringers | |||
16 | If the side arms (3) are reused, remove from the terminals the snap rings (16) before installation, open the protective hoods (15) and apply (A) lubricating grease in advance | After applying the grease, secure the protective hood (15) with the elastic rings (16) and clean around the terminals. | |
17 | Install the side arms (3) at the top of the bracket (5) on the stringer and the bottom of the anti-roll bar (2) eyelet | Use new self-locking nuts (4). | |
.Side arms of front and rear sway bars | |||
18 | Install the wheels if they have been removed | ||
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
19 | Lower the vehicle from the lift | ||
20 | Connect the negative battery cable or turn on the main switch | For vehicles equipped with electronic engines, always observe the recommendations regarding the care with the vehicle electronics. | |
21 | Run a test drive and check the vehicle's cornering behavior |
Air suspension |
Number | Designation | Model 382.154/188 | Model 382.155/189 | ||
BA32.22-B-1012-03C | Supports of rear and front arms of the stabilizer on the stringers | M10x1.5 - class steel 8.0 | Nm | 35 | 35 |
M10x1.5 - class steel 10.9 | Nm | 60 | 60 | ||
M14x1.5 | Nm | 140...160 | 140...160 | ||
M16x1.5 | Nm | 200...240 | 200...240 | ||
M22x1,5 | Nm | 400...480 | 400...480 |
Air suspension |
Number | Designation | Model 382.17/180/181/182/184/185/186/187, 634.001/011/012/014 | Model 634.061/071/081 | ||
BA32.22-B-1012-03C | Supports of rear and front arms of the stabilizer on the stringers | M10x1.5 - class steel 8.0 | Nm | 35 | 35 |
M10x1.5 - class steel 10.9 | Nm | 60 | 60 | ||
M14x1.5 | Nm | 140 ...160 | 140...160 | ||
M16x1.5 | Nm | 200...240 | 200...240 | ||
M22x1,5 | Nm | 400...480 | 400...480 |
Air suspension |
Number | Designation | Model 382.154/188 | Model 382.155/189 | ||
BA32.22-B-1013-03C | Side arms of front and rear sway bars | M12x1.5 | Nm | 100..110 | 100...110 |
M14x1.5 on the holder | Nm | 120...140 | 120...140 | ||
M14x1.5 - on the torsion bar | Nm | 160 | 160 | ||
M16x1.5 | Nm | 230...270 | 230...270 | ||
M20x1.5 - on the holder | Nm | 145,5...217,5 | 145,5...217,5 | ||
A 970 990 00 51 - M20x1.5 | Nm | 215 | 215 | ||
M22x1.5 | Nm | 400...480 | - |
Air suspension |
Number | Designation | Model 382.17/180/181/182/184/185/186/187, 634.001/011/012/014 | Model 634.061/071/081 | ||
BA32.22-B-1013-03C | Side arms of front and rear sway bars | M12x1.5 | Nm | 100...110 | 100...110 |
M14x1.5 on the holder | Nm | 120...140 | 120 ... 144 | ||
M14x1.5 - on the torsion bar | Nm | 160 | 160 | ||
M16x1.5 | Nm | 230...270 | 230...270 | ||
M20x1.5 - on the holder | Nm | 145,5...217,5 | 145,5...217,5 | ||
A 970 990 00 51 - M20x1.5 | Nm | - | - | ||
M22x1.5 | Nm | - | - |
Air suspension |
Number | Designation | Model 382.17/180/181/182/184/185/186/187, 634.001/011/012/014 | Model 634.061/071/081 | ||
BA32.22-B-1015-03C | Stabilizer bearings caps | M 8 | Nm | 25 | 25 |
M10x1,5 | Nm | 35 | 35 | ||
M14x1.5 | Nm | 150...180 | 150...180 | ||
M16x1.5 | Nm | 260...310 | 260...310 | ||
M20x1.5 | Nm | 460...550 | 460...550 | ||
M24x1.5 | Nm | 690...820 | 690...820 |