Shown on model 212 with transmission 725.0 |
1r | Oil line |
1z | Oil line |
2 | Separating points |
3 | Oil cooler |
4 | Clamps |
10 | Clip |
11r | Oil line |
11z | Oil line |
12 | Separating points |
P27.55-2212-05
P27.55-2211-08
Shown on model 212 with engine 642 |
1r | Oil line | 7 | Clip | 14 | Bolts | ||
1z | Oil line | 8 | Oil pan | 15 | Bracket | ||
5 | AdBlue® injection line | 9 | Transmission | 16 | Bolts | ||
6 | Electrical connector | 13 | Heat shield |
Caution | Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil | Wear protective gloves, protective clothing and safety glasses. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Notes on automatic transmission | |||
| Remove/install | ||
1.1 | Remove center and rear section of lower engine compartment paneling. | Transmission 725.0 in model 212 with engine 278 | |
1.2 | Remove front and rear bottom sections of soundproofing. | Transmission 725.0 in model 207 with engine 642 | |
2 | Clean area surrounding connecting point (2) thoroughly. | ||
3 | Disconnect oil line (1r) or oil line (1z) at front connecting points (2). | | |
4 | Seal openings of oil line (1r) or oil line (1z) using suitable stop plugs. | Record plug | |
5 | Release clamp (7). | Transmission 725.0 in model 207 with engine 642 | |
Bolt, metering valve profiled clamp to exhaust system | |||
6 | Release and disconnect electrical connector (6). | Transmission 725.0 in model 207 with engine 642 | |
7 | Detach AdBlue® injection line (5) and place to one side. | Transmission 725.0 in model 207 with engine 642 | |
8 | Lower rack-and-pinion steering. |
| |
9 | Detach corresponding clamps (4) from oil pan (8). | Bolt, bracket for oil line/oil cooling system to oil pan | |
10 | Unscrew screws (14) and remove heat shield (13). | Screw/bolt, heat shield to oil pan | |
11 | Unscrew screws (16) and remove holder (15). | ||
12 | Detach oil line (1r) or oil line (1z), pull out of transmission (9) and seal openings in transmission (9) and oil line (1r) or oil line (1z) using suitable stop plugs. |
| |
Transmission 725.0 in model 207 with engine 642 | |||
| |||
Installation: Replace the O-rings. | |||
Record plug | |||
13 | Detach clamp (10). | Bolt, clamp to oil line | |
14 | Remove radiator grille. |
| |
Transmission 725.0 in model 212 with engine 278 | |||
Transmission 725.0 in model 212 with engine 278 | |||
15 | Clean area surrounding oil line (11r) or oil line (11z) on oil cooler (3) thoroughly. | ||
16 | Disconnect oil line (11r) or oil line (11z) at front from oil cooler (3) at connecting points (12). | | |
17 | Collect escaping transmission oil in a suitable container and seal connection fittings with suitable stop plugs. | Record plug | |
18 | Take oil line (11r) or oil line (11z) out downward. | ||
19 | Install in the reverse order | ||
| Check | ||
20 | Check transmission oil level and correct if necessary. | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
21 | Carry out engine test run and check transmission (9) and oil lines (1r, 1z, 11r, 11z) for leak tightness. |
129 589 00 91 00
Record plug