B26.60-6693-06
Represented in the gearbox 712.453
1 Selection cable
2 Coupling cable
3 Support (coupling cable)
4 Screw
5 Screw
6 Selection (selection cable)
7 Ball terminal
8 Selection lever
9 Counterweighted
10 Ball terminal
11 Nut
| Remove | ||
Danger! | Risk of death due to vehicle sliding or tilting from the lifting device | Position the vehicle on an appropriate lifting device so that the front, rear shaft wheels, drive axle and guided shaft wheels remain safely supported on the lifting device support plates, at the lifting points defined by the manufacturer of the vehicle . | |
1 | Position the vehicle on a leveled and flat area | ||
2 | Turn of the general key | ||
3 | Actuate the parking brake; | ||
Danger! | Risk of injury due to pinching and crushing when tilting the cabin | When tilting the cabin forward and backwards, do not enter the tilting area and take preventive measures to hinder non-authorized people from entering the area. Always tilt the cabin to the final position and lock it with a safety device. | |
4 | Tilt the cabin | ||
| Information on cabin tilting | ||
5 | Put the shift lever in neutral position | ||
6 | Remove the ball terminal (7) in the selection lever (8) | The ball terminal (7) fits under pressure in the gear shifting lever (8). Loosen only the nuts (11) when replacing the cable. | |
7 | Loosen the screws (5) on the gear selection (1) cable support (6) | ||
8 | Remove the ball terminal (10) in the counterweight (9) | The ball terminal (10) fits under pressure into the counterweight (9). Loosen only the nuts (11) when replacing the cable. | |
9 | Loosen the screws (4) on the gear coupling (2) cable support (3) | ||
| Clean | ||
10 | Clean all components | Do not use chemical cleaning products such as solvents, gasoline, etc. | |
Dry clean all gear lever components connected to the gearbox, drive cables and protective boots. | |||
| Check | ||
11 | Check gear lever components at the gearshift | Check for wear and damages, replace components as necessary. | |
12 | If necessary, before the assembly, apply grease to the selection cables ball terminals and gear couplings | ||
| Install | ||
13 | Check if the operating lever is neutral position in the cabin | ||
14 | Install the gear coupling cable (2) support (3) and tighten the screws (4) | ||
Fasten the lower gear lever support (coupling cable) | |||
15 | Fit the gear coupling cable (2) ball terminal (10) to the counterweight (9) | ||
16 | Install the gear selection cable (1) support (6) and tighten the screws (5) | ||
Fasten the upper gear lever support (selection cable) | |||
17 | Fit the gear selection cable (1) ball terminal (7) to the selection lever (8) | ||
18 | Perform a function test | ||
Danger! | Risk of injury due to pinching and crushing when tilting the cabin | When tilting the cabin forward and backwards, do not enter the tilting area and take preventive measures to hinder non-authorized people from entering the area. Always tilt the cabin to the final position and lock it with a safety device. | |
19 | Tilt the cabin | ||
| Information on cabin tilting | ||
20 | Connect the general key |
Shift mechanism
Número | Denominação | Gearbox 712.453/454; 745.455/456 | |||
BA26.60-B-1010-01A | Mounting of upper shifting lever bracket (gear selection cable) | Nm | 23 | ||
BA26.60-B-1011-01A | Mounting of lower shifting lever bracket (gear engagement cable) | Nm | 23 | ||
Produtos para reparos
Número | Denominação | Número de pedido |
BR00.45-B-1007-06A | Grease DBL 6812.00 | Klueber Lubrification |