Remove/install rear engine mount

AR22.10-P-1160AK

19.4.04

ENGINE 266.920 /940 /960 /980 in MODEL 169.0 /3, 245.2

Shown on engine 266.920

1 Collar bolt

2 Bolts

3 Bolt

4 Right rear engine mount

5 Left rear engine mount

P22.10-2209-03

	Remove
Danger!	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates below the hoist support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
1	Remove air filter housing		AR09.10-P-1050AK
2	Take off coolant expansion reservoir and place to the side with coolant lines connected		AR20.30-P-4950AK
3	Lift up engine with engine bridge	 Only lift up the engine until the engine mounts are relieved of load.	AR22.10-P-1260-01AL
			*169589006100
4	Remove rear part of fender liner in right front fender	Model 169.1690/3	AR88.10-P-1300AK
		Model 245.2	AR88.10-P-1300BK
5	Remove lower engine compartment paneling	With rough road package code 484	AR61.20-P-1105AL
		Without rough road package code 484	AR61.20-P-1105AM
6	Unscrew collar bolts (1) and bolts (2, 3), remove the right rear engine mount (4) and the left rear engine mount (5)
	Install
7	Insert the right rear engine mount (4) and the left rear engine mount (5) into the front axle carrier, attach the bolts (2, 3)	 Do not tighten screws (2, 3). The installation location of the rear right engine mount (4) and the rear left engine mount (5) is preset by a locating pin on the engine support.
8	Loosen the nuts on both the front engine mounts on the front axle carrier	 The right rear engine mount (4) and the left rear engine mount (5) must first be secured to the front axle carrier, otherwise strain between the major assembly and the vehicle can result.
9	Lower the engine until the collar bolt (1) can be inserted. Tighten collar bolt (1)		AR22.10-P-1260-01AL
			*BA22.10-P-1004-01T
			*169589006100
10	Tighten bolts (2) then tighten bolt (3)		*BA22.10-P-1003-01T
11	Tighten the nuts on both the front engine mounts on the front axle carrier	 Ensure that the front engine mounts are not twisted while tightening the nuts. Incorrect installation positions can lead to bracing between the major assembly and the vehicle.
			*BA22.10-P-1001-01T
12	Fit rear part of fender liner in right front fender	Model 169.1690/3	AR88.10-P-1300AK
		Model 245.2	AR88.10-P-1300BK
13	Install bottom engine compartment panel	With rough road package code 484	AR61.20-P-1105AL
		Without rough road package code 484	AR61.20-P-1105AM
14	Detach the motor crossmember		AR22.10-P-1260-01AL
			*BA32.25-P-1002-04J
			*169589006100
15	Install coolant expansion reservoir		AR20.30-P-4950AK
16	Install air filter housing		AR09.10-P-1050AK

 Engine suspension, engine mounts, engine supports

Number	Designation		Engine 266 in model 169	Engine 266 in model 245


BA22.10-P-1001-01T	Nut of front engine mount to front axle carrier	Nm	55	55
BA22.10-P-1003-01T	Bolt, rear engine mount to front axle carrier	Nm	25	25
BA22.10-P-1004-01T	Bolt of rear engine mount to engine support	Nm	80	80

 Struts

Number	Designation			Model 169	Model 245


BA32.25-P-1002-04J	Bolt of suspension strut to suspension strut dome	1st stage	Nm	20	20
		2nd stage	°	45	45

Motor crossmember

169 589 00 61 00

เอกสารที่อ้างถึง