ar1518s100005ps
Disconnect/connect engine wiring harness to remove engine
ประเภท ar · หัวข้อ 15.18 · เวอร์ชัน 0100 · 2018-12-14
ใช้กับ: Engine 642 in model 470, 471
ไม่มีใน “th” แสดงเป็น อังกฤษ
ตำแหน่ง
กลุ่มฟังก์ชัน 1 Engine › 15 Electrical system - engine › 15.18 Cable sets — ซีรีส์ 470 · ซีรีส์ 471
EinPAS 25 On-board/network/multifunction › 25.25 Main wiring harness › 25.25.20 Engine wiring harness — ซีรีส์ 470 · ซีรีส์ 471
ใช้กับเครื่องยนต์/เกียร์ด้วย: 642 ***
AR15.18-S-1000-05PS
| Disconnect/connect engine wiring harness to remove engine
|
|
|
Topical note
| Information on preventing damage to electronic components due to electrostatic discharge
|
| AH54.00-P-0001-01A
|
Engine
| 642 in model 470, 471
|
Headless screws/bolts: screws/bolts and nuts, coarse-pitch thread
|
Number
| Designation
|
|
| 8.8
| 10.9
|
BA00.10-N-1002-01A
| M6
| Galvanized
| Nm
| 9
| 13
|
|
|
| Phosphated
| Nm
| 9
| 12
|
Headless screws/bolts: screws/bolts and nuts, coarse-pitch thread
|
Number
| Designation
|
|
| 12.9
|
BA00.10-N-1002-01A
| M6
| Galvanized
| Nm
| 16
|
|
|
| Phosphated
| Nm
| 14
|
Headless screws/bolts: screws/bolts and nuts, coarse-pitch thread
|
Number
| Designation
|
|
| 8.8
| 10.9
|
BA00.10-N-1003-01A
| M8
| Galvanized
| Nm
| 23
| 32
|
|
|
| Phosphated
| Nm
| 21
| 29
|
Headless screws/bolts: screws/bolts and nuts, coarse-pitch thread
|
Number
| Designation
|
|
| 12.9
|
BA00.10-N-1003-01A
| M8
| Galvanized
| Nm
| 38
|
|
|
| Phosphated
| Nm
| 36
|
Number
| Designation
|
| Engine 642 in model 470, 471
|
BA15.40-N-1002-01PS
| Screw/bolt, alternator to crankcase
| Nm
| 20
|
Battery, voltage supply
|
Number
| Designation
|
| Model 471
| Model 470
|
BA54.10-N-1003-01P
| Nut, electric line to prefuse box
| Nm
| 13
| 13
|
1
| Open clamps (2) and release engine wiring harness (1) from clamps (2).
|
2
| Unclip fuse box (3) in an upward direction.
|
3
| Unclip and remove cover of fuse box (3).
|
5
| Remove electric line (5) from fuse box (3) .
|
6
| Remove electric line (6) from prefuse box (7) .
|
7
| Disconnect electrical connector (8) from prefuse box (7).
|
8
| Place engine wiring harness (1) on engine.
|
9
| Remove ground line (12) at alternator .
|
10
| Open clamps (10) and release engine wiring harness (1) from clamps (10).
|
11
| Release cover of fuse and relay housing (11) and remove it.
|
|
| WIS Service Media
wsm://04_ 201800_41
Operation steps 11 to 13 are shown.
|
12
| Release fuse and relay module (14) and place to one side with lines connected.
|
13
| Disconnect electrical connectors (15).
|
14
| Remove cover (13) in an upward direction and guide engine wiring harness (1) out of fuse and relay housing.
|
15
| Disconnect ground line (16) from body .
|
16
| Place engine wiring harness (1) on the engine.
|
17
| Connect in reverse order.
|
เอกสารที่อ้างถึง
