Shown on MODEL 222 |
01 | Headlamp aimer |
A | Distance |
P82.10-7550-06
Shown on MODEL 222 |
E1 | Left front lamp unit |
E1e15 | Left low beam (short range) |
E1e16 | Left low beam (long range) |
P82.10-7548-01
Light gradient for low beams |
1 | Light-dark boundary |
2 | Reference line for height adjustment |
3 | Central mark |
4 | Reference line for lateral setting |
P82.10-7547-76
Shown on MODEL 222 |
H | Height adjusting screw |
P82.10-7557-01
Light gradient for diagnostic light pattern |
1 | Light-dark boundary |
2 | Reference line for height adjustment |
3 | Central mark |
P82.10-7559-01
Danger ! | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
| General information on checking/correcting headlamp adjustment | ||
Preparatory tasks | |||
1 | Determine degree of inclination for main headlamps | ||
| Notes on determining headlamp aiming values | ||
The degree of inclination for the main headlamps is specified on the model plate on the B-pillar on the passenger side. | |||
2 | Park the vehicle on a horizontal, level surface | Maximum permissible height difference of surface for: | |
3 | Align headlamp aimer (01) | ||
| 000 588 11 21 00 Adjustment device | ||
| |||
Align the headlamp aimer (01) at a distance (A) of approx. 30 cm in front of the left or right front lamp unit (E1) level with the left or right low beam headlamp (long range) (E1e16) parallel to the front of the vehicle. | |||
4 | Set specified degree of inclination for main headlamps at headlamp aimer (01) | ||
5 | Switch on low beam at exterior lights switch | When testing and adjusting the low beams, make sure that the extended fog light function is not active. | |
Check and, if necessary, adjust (checking and adjustment of the low beams is described at the left low beam headlamp (long range) (E1e16); the same procedure is used for the right side.) | |||
6 | Check height adjustment of left low beam headlamp (long range) (E1e16); adjust if necessary | If the height adjustment is correct, the light-dark boundary (1) of the light gradient for the left low beam headlamp (long range) (E1e16) to the left of the center mark (3) must be congruent with the reference line for the height adjustment (2) in the headlamp aimer (01), corresponding to the colored representation. The colored area of the light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) must be above the reference line for the height adjustment (2), corresponding to the colored representation. | |
If the height adjustment of the left low beam headlamp (long range) (E1e16) is not correct: | |||
| |||
Perform zero position adjustment using diagnostic system in suspension control unit. | |||
| |||
| |||
Prepare alignment of headlamp aimer (01). | |||
| |||
Switch on rectangular diagnostic light pattern using diagnostic system. | |||
| |||
| |||
When the diagnostic light pattern is switched on and the height adjustment is correct, the horizontal light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) to the left of the center mark (3) must be congruent with the reference line for the height adjustment (2) in the headlamp aimer (01). The colored area of the light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) must be above the reference line for the height adjustment (2). | |||
If the height adjustment of the left low beam headlamp (long range) (E1e16) is not correct with the diagnostic light pattern switched on: | |||
| |||
Turn the adjustment screw for the height adjustment (H) to correct the height adjustment of the left low beam headlamp (long range) (E1e16). | |||
7 | Check lateral adjustment of left low beam headlamp (long range) (E1e16); adjust if necessary | If the lateral adjustment is correct, the light-dark boundary (1) of the light gradient for the left low beam headlamp (long range) (E1e16) starting at the center mark (3) on the right must be congruent with the reference line for the lateral adjustment (4) in the headlamp aimer (01), corresponding to the colored representation. The colored area of the light-dark boundary (1) of the left low beam headlamp (long range) (E1e16) must be above the reference line for the lateral adjustment (4), corresponding to the colored representation. | |
If the lateral adjustment of the left low beam headlamp (long range) (E1e16) is not correct with the diagnostics light pattern already switched on: | |||
| |||
Subject to a separate repair order, check and correct the installation position of the headlamp concerned. Then perform operation steps 2 to 7 again. | |||
Gap dimensionBumper to headlamp | |||
If the height adjustment of the left low beam headlamp (long range) (E1e16) was correct and the lateral adjustment of the left low beam headlamp (long range) (E1e16) is not correct: | |||
| |||
Perform zero position adjustment using diagnostic system in suspension control unit. | |||
| |||
| |||
Prepare alignment of headlamp aimer (01). | |||
| |||
Switch on rectangular diagnostic light pattern using diagnostic system. | |||
| |||
| |||
Check the height adjustment of the left low beam headlamp (long range) (E1e16) again with the diagnostic light pattern switched on; if necessary, correct by turning the adjustment screw for the height adjustment (H). | |||
| |||
Check the lateral adjustment of the left low beam headlamp (long range) (E1e16). | |||
| |||
If the lateral adjustment of the left low beam headlamp (long range) (E1e16) is not correct with the diagnostics light pattern already switched on: | |||
| |||
Subject to a separate repair order, check and correct the installation position of the headlamp concerned. Then perform operation steps 2 to 7 again. | |||
Gap dimensionBumper to headlamp | |||
Concluding tasks | |||
8 | Reset switch positions to input condition | Only if the high beam setting is not to be checked afterwards. |