Shown on model 470.2 |
1 | Front mud guard |
S88.30-4612-06
S88.30-4613-08
Shown on model 470.2 on the left side of the vehicle |
1 | Front mud guard | 3 | Fender | 5 | Screw | ||
2 | Fender liner | 4 | Bolts |
Shown on model 470.2 on the right side of the vehicle |
1 | Front mud guard |
2 | Fender liner |
4 | Bolts |
6 | Expansion rivet |
S88.30-4618-05
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
| Remove | ||
1 | Raise vehicle. | ||
Topical note | Special instructions for lifting and supporting vehicle | ||
| |||
2 | Remove screws (4, 5) from left fender liner (2). | To do this, turn left wheel and tire assembly (to make space). | |
3 | Remove screws (4, 5) from right fender liner (2). | To do this, turn right wheel and tire assembly (to make space). | |
| Clean | ||
4 | Clean right fender liner (2) and right fender (3) in the contact area of the front mud flap (1). | Cleaner | |
| Check | ||
5 | Check design of the delivered front mud flaps (1). | When designing the front mud flaps (1) with holes (arrows A), additional operation steps must be carried out. | |
| Install | ||
6 | Position front right mud flap (1) on right fender (3) and screw in screws (4, 5). | Ensure that the front mud flap (1) is positioned flush on the fender (3) (arrows B). | |
7 | Drill front right mud flap (1) and right fender liner (2) through existing holes (arrows A) with a diameter of 7.5 mm. | For the design of the front mud flaps (1) with holes (arrows A). | |
Commercially available devices/tools | |||
8 | Deburr holes (arrows A) in front right mud flap (1). | For the design of the front mud flaps (1) with holes (arrows A). | |
9 | Position front right mud flap (1) on the right fender liner (2) and attach expansion rivets (6). | For the design of the front mud flaps (1) with holes (arrows A). | |
Use expansion rivets (6) provided in the parts kit. | |||
| Clean | ||
10 | Clean left fender liner (2) and left fender (3) in the contact area of the front mud flap (1). | To do this, turn left wheel and tire assembly (to make space). | |
| Install | ||
11 | Position front left mud flap (1) on left fender (3) and screw in screws (4, 5). | Ensure that the front mud flap (1) is positioned flush on the fender (3) (arrows B). | |
12 | Drill front left mud flap (1) and left fender liner (2) through existing holes (arrows A) with a diameter of 7.5 mm. | For the design of the front mud flaps (1) with holes (arrows A). | |
Commercially available devices/tools | |||
13 | Deburr holes (arrows A) in front left mud flap (1). | For the design of the front mud flaps (1) with holes (arrows A). | |
14 | Position front left mud flap (1) on left fender liner (2) and attach expansion rivets (6). | For the design of the front mud flaps (1) with holes (arrows A). | |
Use expansion rivets (6) provided in the parts kit. | |||
15 | Lower vehicle. | ||
16 | Supplement special equipment in Vehicle Documentation (VeDoc). | Designation of the affected special equipment: Code P47 (front mud flap). |